How do you wire a Lutron occupancy sensor?
Push the wires back into the wallbox. And mount the occupancy sensor to the wall box using the screws that came with the sensor tighten the screws until the sensor is tight against the wall.
How do you adjust the occupancy sensor on a light switch?
In vacancy mode you have to push the button to turn the load on to adjust the range turn the knob from the center default position of 65%.
How do you program and configure your Lutron Maestro motion sensor light switch?
One. Two three times okay so again you can program the occupancy switch timeout. Period by pressing and holding this big button right here.
How do you program a Lutron motion sensor?
So all we have to do to set this to whatever mode we want you just simply push and hold on this button right here and uh we’re gonna wait and in about five seconds it’s gonna start blinking.
How do you wire a motion sensor to an existing light?
How to Add Motion Sensors to Existing Outdoor Lights
- Pick an outdoor motion sensor kit online. First, make sure the existing light has an opening to screw into.
- Turn the power off to the light, and remove the cover.
- Remove the insert.
- Run the wires into the light.
- Connect the wires.
- Adjust the sensitivity.
Will a motion light work without a ground wire?
Electrically the device will function the same if you connect it to a ground wire or a neutral.
Why does my sensor light keep going on and off?
Faulty wires, bulbs that do not work or are dead, and bad electrical connections are all reasons why your motion sensor lights might be turning on and off. If it is on a high sensitivity level, it may be detecting too much movement.
How do I reset my occupancy sensor?
How to Reset a Motion Sensor Light | Lighting and Ceiling Fans – YouTube
How do I keep my motion sensor light on all the time?
You can constantly keep a motion sensor light by wiring it with a double switch or three-position switch set up to bypass the sensor in one position. Alternatively, most motion sensors will keep a light on if you switch the sensor off and then on again quickly.
How do I reset my motion light stays on all the time?
Reset your Motion Detector – To reset your motion light, unplug it from its power source for a full 10 seconds. Plug it back in and allow it to come back on. This should reset your light and turn off the auto-on function.
How do I reset my Lutron motion sensor?
Step 1: Quickly triple tap and hold the Test or Light button on the Sensor. DO NOT release after third tap. Step 2: Keep the button pressed after the third tap for a few seconds until the dome LED begins to flash slowly (approximately once per second). The Sensor has now been returned to Factory Default Settings.
How do you reset a motion sensor light switch?
Can I connect red and black wires together?
These wires are typically used for switch wiring as well as the interconnection between smoke detectors hard-wired into the power system. You can link two red wires together, or you can link a red wire to a black wire. Since red wires conduct current, they are considered hot.
What is the red wire on a motion sensor light?
A two-way sensor switch will have either two black or one black and one red wire, plus in all cases a green ground wire. The red wire must go to the switch leg (the wire actually powering the light fixture) for the switch to operate properly.
What happens if I dont ground my light fixture?
Accidentally touching the metal casing of an appliance that’s not grounded and experiencing a surge of electrical current can result in serious injury. Grounding helps prevent these kinds of accidents from occurring.
What happens if an outdoor light is not grounded?
Every light fixture in your house must be properly grounded, and this requirement is even more important for those outside. If a fixture isn’t grounded, someone can get a shock just by touching it, and that’s more dangerous in moist outdoor conditions than it is indoors.
How do I reset my sensor light?
How do I stop my sensor light from blinking?
If your motion sensor lights keep flashing on and off, you should try: Checking whether they’re actually flashing on and off or just flickering. Adjusting the motion sensor positioning and settings. Adding “side blinders” to your sensor.
What are the 3 settings on a motion sensor light?
Most Motion sensors will either have LUX , TIME and SENSITIVITY some only have LUX and TIME.
How do you stop motion sensor lights from turning off?
Here are 4 ways to stop a motion sensor light from turning off:
- Turn the light off and on again very quickly.
- Adjust the motion sensor sensitivity.
- Bypass the motion sensor.
- Have the motion sensors adjusted by a qualified professional.
Why won’t my motion sensor lights turn off?
The Problem
Some movement sensors have a built-in override functionality. If the override function is engaged, the sensor light will stay on until the override function is disengaged. This override function is often engaged accidentally which causes confusion and the mistaken belief that the sensor is faulty!
Why is my motion light staying on all the time?
What Causes my Light to Stay On? Several things can cause your motion detector to stay on, including age, storm damage, a power surge, improper installation, and improper settings. A few issues are easy to correct without professional help.
Why is my Lutron switch blinking red?
If the switch indicator LED is flashing red, that typically means that you are near or below the minimul load size for the switch.
How do I reset my outside light sensor?
What is the extra red wire for?
Standard House Wiring Colors
In the standard wire color code, the hot wire in a cable with two conductors plus ground is black, and the extra hot wire in a three-conductor set is red. The standard ground wire color is either bare copper or green.