What is GFO fiber?
Packings with 100% GORE GFO Fiber can provide maintenance engineers with consistently high performance general service packing for wide application and use, including sealing shafts on high-speed pumps, mixers, agitators or any other equipment with rotating or reciprocating shafts.
What is shaft packing?
A stuffing box—also called a stuffing gland, packing gland or packing box—forms a seal between the prop shaft and the hole in the hull through which the shaft passes while allowing the shaft to turn freely. It consists of a threaded sleeve and a hollow nut, through which the prop shaft passes.
What size shaft packing do I need?
The most accurate method is to measure the inside diameter of the packing nut and subtract 1.25″ shaft diameter and then divide by 2. FWIW, I have a h40. 5 with a 1.25″ shaft and my packing is 3/16″. I guessed once, bought 1/4″ and after struggling for a while I bought some 3/16″ that went in exactly like it should.
What is graphite packing?
Graphite packing is a highly resistant sealant used in systems with valves, faucets, and stuffing boxes, as well as other machines with watertight mechanical parts. It can be applied either to static valve stems or to moving joints.
How long does shaft packing last?
In a powerboat used regularly, the shaft packing should be replaced at least every other year. Sailboats may not need to have the packing replaced for five years or more, but when the stuffing box starts requiring frequent adjustment or if it begins to feel warm, it’s time. Repacking is straightforward.
What is the difference between packing and mechanical seal?
When considering gland packing vs mechanical seal solutions, mechanical seals are the best for minimizing sleeve damage. Packing seals are removed and replaced much more often than mechanical seals, which causes considerable wear and tear to the pumps as they are disassembled and reassembled.
How often should pump packing be replaced?
around 2 to 3 years
Most packing, if properly maintained during the pump’s operation, should last around 2 to 3 years. When it is time to replace it, how much of a project it is depends on the type of fire pump you have.
What size packing do I need for a 2 shaft?
With few exceptions, these are specifically matched to the shaft diameter, a 2-inch shaft, for instance, utilizes three 3/8-inch packing while 1-1/2-inch shaft utilizes 1/4-inch packing. Therefore, if you know your shaft diameter, obtaining the correct size packing is straightforward.
Which is better graphite or PTFE?
Graphite packings can be a conductor of heat. PTFE is a strong resin with low coefficient of friction as well. It is highly resistant to different kinds of substances such as aggressive chemicals, acids, gases etc. Teflon is a variant of PTFE that is widely used for making non-stick cookware.
What is PTFE packing?
In simple terms, packing materials made of PTFE or polytetrafluoroethylene are known as PTFE packings. These are sealants offering mechanical compression for complex applications across industries. You can find them being used extensively in industrial plants dealing with oxidising media or corrosive chemicals.
How much should packing leak?
10-15 drops per minute
Packing is expected to leak. It is common practice to try to control the leaking to 10-15 drops per minute. To maintain this rate, the packing must be monitored and adjusted daily. The leakage cools and lubricates the packing.
What is packing and seal?
Packing seal refers to a dynamic sealing device that generates a pressing force between the packing and the rotating and fixed parts through pre-tensioning or self-tightening of the medium pressure.
What happens if packing is too tight on a pump?
A packing gland that is too tight can also cause the pump to draw more power. When packing is compressed, it squeezes tightly around the shaft sleeve causing additional drag on the shaft.
Is packing supposed to leak?
All packing manufacturers recommend a slight leakage through the packing for accomplishing water lubrication. There is a definite relationship of leakage rate to max- imum life of packing. Less than the recommended leakage rate will tend to reduce the life factor.
Can you repack a stuffing box in the water?
While it may be possible in some cases to repack a stuffing box with the vessel in the water, it’s a lot easier (and recommended here) to do it while the vessel is hauled. Experts recommend hauling any type of boat before servicing the stuffing box.
How much should a stuffing box drip?
two to three drops per minute
When properly adjusted, stuffing boxes are designed to “leak” slightly at two to three drops per minute while the engine is running and the shaft is turning. There should be no dripping when the boat is at rest and the shaft is not spinning.
What does PTFE packing mean?
Is PTFE a graphite?
Graphite packings and PTFE Packings are popular sealants generally available in braided style. The biggest difference between both these packings is that graphite is a naturally occurring form of carbon and PTFE is a synthetic material.
What is the meaning of PTFE?
polytetrafluoroethylene (PTFE), a strong, tough, waxy, nonflammable synthetic resin produced by the polymerization of tetrafluoroethylene.
What is packing seal made of?
There are many types of packing sealing structure, which are mainly composed of packing, stuffing box and packing fixing parts. Commonly used filler materials include asbestos fabric, carbon fiber, rubber, flexible graphite, and engineering plastics.
What are the types of mechanical packing?
Essentially, there are 3 main construction types of mechanical packing generally available on the marketplace.
…
These materials are generally application-specific, and it is important for users of packing to select the optimal material for their application at hand.
- Braid-over-braid.
- Interlocked.
- Plaited.
How long should pump packing last?
Do packing rings require lubricant to seal?
Packing requires lubrication to keep it cool and to flush corrosive chemicals and abrasive particles. It’s often necessary to flush the lantern ring from an external source, especially if the pumped product is contaminated or very abrasive.
How often should you repack your stuffing box?
every two to three years
While it depends on the number of hours a vessel is utilized, most powerboat owners should repack their stuffing box every two to three years. Sailboat owners (due to typically lower engine hours) should repacking every three to four years.
How often should a stuffing box drip?
three drops per minute
Water is required to lubricate conventional packing, so a properly adjusted stuffing box can be watertight when the shaft is stopped, but it must drip when the shaft is turning. Two or three drops per minute are adequate.