How do I reset my outdoor motion sensor?
Turn your light switch on and off quickly, hitting each position four times. When the light comes on, turn the switch to the off position and wait five to seven seconds before turning it on again. The light should remain off and the motion detection unit should be reset.
How do I adjust the sensitivity on my motion detector?
Slide the sensor up off of its back plate. On the back, you should see Sensitivity (H for “high” on top, LO for “low” on bottom) on the right and Pet Sensitivity (small dog image on top, large dog image on bottom) on the left. Pull out the switches and move them to the appropriate setting.
Why is my motion sensor flashing?
Flickering lights (lights that produce unsteady, rapid changes in brightness) are usually caused by one of 3 things: A bad bulb. Bad connection between the bulb and the light fixture. Problems within the circuit.
How do I change the battery in my motion detector?
Next you must release the lens from the device by depressing three tabs on the device. Two on top and one on the bottom. Next remove the batteries insert the new batteries. Pay attention to polarity.
What are the 3 settings on a motion sensor light?
There are 3 settings on a motion sensor light: sensitivity, timer, and lux. These 3 settings determine how sensitive the light is to movement, how long the light will stay on after detecting movement, and what level of darkness the light will turn on in.
How do I reset my motion light stays on all the time?
Reset your Motion Detector – To reset your motion light, unplug it from its power source for a full 10 seconds. Plug it back in and allow it to come back on. This should reset your light and turn off the auto-on function.
How do you adjust a motion sensor switch?
How to Adjust Intermatic Occupancy/Vacancy Sensors
What does red light on motion sensor light mean?
The flashing red light on a motion detector indicates that the device is in its walk test mode. In this mode, a user can walk around the area and check to make sure that motion is being detected. If the device is not flashing red, then it is not detecting motion, and the position of the sensor will need to be adjusted.
How do you stop motion sensor lights from turning off?
Here are 4 ways to stop a motion sensor light from turning off:
- Turn the light off and on again very quickly.
- Adjust the motion sensor sensitivity.
- Bypass the motion sensor.
- Have the motion sensors adjusted by a qualified professional.
Is there a battery in a motion sensor?
Yes, wireless motion sensors have batteries. All wireless sensors use batteries to communicate with the panel. Wireless motion sensors also require power for basic operation. However, hardwired sensors do not require batteries, as they can use power that is provided from the panel.
What kind of battery does a motion sensor take?
CR123A 3 volt battery
The motion detector requires one CR123A 3 volt battery. This battery can be purchased at your local hardware, mass retailer or battery store.
Why does my motion sensor light stay on during the day?
What Causes my Light to Stay On? Several things can cause your motion detector to stay on, including age, storm damage, a power surge, improper installation, and improper settings. A few issues are easy to correct without professional help.
Why won’t my motion sensor lights turn off?
The Problem
Some movement sensors have a built-in override functionality. If the override function is engaged, the sensor light will stay on until the override function is disengaged. This override function is often engaged accidentally which causes confusion and the mistaken belief that the sensor is faulty!
Why is my motion light staying on all the time?
Why does my sensor light keep going on and off?
Faulty wires, bulbs that do not work or are dead, and bad electrical connections are all reasons why your motion sensor lights might be turning on and off. If it is on a high sensitivity level, it may be detecting too much movement.
How do I make my motion sensor light stay on all the time?
You can constantly keep a motion sensor light by wiring it with a double switch or three-position switch set up to bypass the sensor in one position. Alternatively, most motion sensors will keep a light on if you switch the sensor off and then on again quickly.
How do you reset a motion sensor light switch?
How to Reset a Motion Sensor Light | Lighting and Ceiling Fans – YouTube
How long do motion sensor light batteries last?
How long do the batteries supplied last in the motion detector and magnet contact? Battery life varies by use. On average, these will last one year. If the sensors are positioned where they are frequently detected, this will affect battery life and shorten battery life.
How do you test to see if a motion detector is working correctly?
Walk across the sensors field of view, the LED will illuminate when it detects motion. It is best to walk across the sensor, rather than directly towards the sensor. The sensor will repeat this process of waiting 30 seconds then lighting up as it sees motion. It will stay in the test mode for 3 minutes.
Why does my motion light keep going on and off?
A motion light switching on and off could be due to many reasons. Incompatible LED bulbs are common, but also, the sensor may be faulty or damaged power bumps, or even spiders. Try changing the bulb, resetting the sensitivity, or replacing the sensor if nothing else works.
How do you stop a motion sensor light from turning off?
How long do motion sensor lights stay on?
On average, a motion detector light will stay on for up to 20 minutes. That amount of time is extended each time a sensor detects fresh movement, so it is possible for a motion detector light to stay on for much longer than 20 minutes at a time.
What is life expectancy of a motion sensor?
Advantages of motion sensor
➨It has more lifespan which is about 100000 Hrs (Active type). ➨It helps in providing security by detecting suspicious movement. ➨It is easy to install motion sensors.
How do you clean motion sensors?
Clean the sensor. Use a soft cloth moistened with a cleaning solution such as window cleaner. Remove accumulation of dust and mildew, as well as any insects and spider webs from the fixture and bulb. Pay particular attention to cleaning the lens of the infrared sensor that switches the light on when motion is detected.
How do you trick a motion sensor to stay on?
To keep a motion sensor light on, you can add a bypass switch to independently power the light, quickly switching the motion sensor ON&OFF to get the sensor stuck at ON position, or use a motion sensor light switch with an ON/OFF feature to keep indoor lights ON.