How do I find running configuration on HP Router?

12/09/202212/09/2022 | Sarah HendricksonSarah Hendrickson | 0 Comment | 12:00 am

How do I find running configuration on HP Router?

To display the running configuration using the WebAgent: In the navigation pane, click Troubleshooting. Click Configuration Report. Use the right-side scroll bar to scroll through the configuration listing.

How do I turn on my HP switch web interface?

To enable web login, log in to the device via the console port, and perform the following configuration: • Enable HTTP or HTTPS service • Configure the IP address of the VLAN interface • Configure a username and password The device supports the following web login methods: • HTTP login: • HTTPS login: The following …

How do I check my HP switch settings?

The options provided in this feature allow you to display all the configurations on a specified interface or VLAN with a single command. You can use the options with the startup config command, show config, and the running config command, show running-config.

How do I get the logs on my HP switch?

To display the Event Log from the Main Menu, select Event Log . An event log display shows a sample event log display.

What is the CLI command of the router to show the contents of startup configuration?

To display the contents of NVRAM (if present and valid) or to show the configuration file pointed to by the CONFIG_FILE environment variable, use the show startup-config EXEC command.

Do show running-config command?

The show running-config command displays the current running configuration on the FWSM. You can use the running-config keyword only in the show running-config command. You cannot use this keyword with no or clear, or as a standalone command, because the CLI treats it as a nonsupported command.

How do I configure my HP switch?

How to: Configure a HP ProCurve switch

  1. Step 1: Connect your serial connection.
  2. Step 2: Conenct PuTTY.
  3. Step 3: Get the IP address.
  4. Step 4: Set time server.
  5. Step 5: Set SNMP community info.
  6. Step 6: Launch the web GUI.
  7. Step 7: Configure basic info.
  8. Step 8: Create VLANs.

What is the default IP of HP switch?

192.168.2.10

The HP ProCurve Switch 1700 Series has a default IP address of 192.168. 2.10 with a subnet mask of 255.255.

How do I know my switch configuration?

  1. Step 1: Inspect your hardware. Check the model number of your shiny new switch.
  2. Step 2: Set up management IP.
  3. Step 3: Check VTP revision number.
  4. Step 4: Configure access ports.
  5. Step 5: Configure trunk ports.
  6. Step 6: Configure access ports.
  7. Step 7: Set up VTY line config.

How do I program my HP switch?

How do I backup my HP switch using putty?

2 Replies

  1. If you use putty run the “sh run” command, this gives you the complete configuration of the switch.
  2. Starting at the bottom, select the most right pixel, drag you mouse to the left, and than up, until you see your “sh run” command.
  3. Hit enter (it is now copied to your clipboard)

How do I check the logs on my Aruba controller?

Navigate to Maintenance > File / Copy Logs. You can directly download logs from the controller by checking the “Download Logs” radio button and clicking Apply.

How do I check router configuration commands?

Configure the router to boot up without reading the configuration memory (nonvolatile RAM, or NVRAM). This is sometimes called the “test system mode.”
…

Task Command
Disable Cisco Discovery Protocol on an interface. no cdp enable
Enable Cisco Discovery Protocol on an interface. cdp enable

What is the command for startup-config?

In Windows 7, you can use the System Configuration Utility or MSConfig to manage start-up applications. This tool allows us to disable or enable the startup items. To run this inbuilt utility, we type msconfig in start search and hit Enter.

What is configuration command?

Use the CONFIG command to change or check the configuration of the system. You can use the CONFIG command to change the online or offline status of available processors, storage amounts, storage ranges, central storage elements, PCIE function identifiers (PFIDs), storage-class memory (SCM), and channel paths: Directly.

What is show ip route command?

On a Cisco router, the show ip route command is used to display the IPv4 routing table of a router. A router provides additional route information, including how the route was learned, how long the route has been in the table, and which specific interface to use to get to a predefined destination.

What is IP default gateway command?

In the Command Prompt window, type “ipconfig” and press “Enter/Return” on your keyboard. You will see a lot of information generated in this window. If you scroll up you should see “Default Gateway” with the device’s IP address listed to the right of it.

How do I find the IP address of my HP switch?

CLI: Configuring IP Address, Gateway, and Time-To-Live (TTL)

  1. show ip.
  2. HP Switch> show ip. Internet (IP) Service. IP Routing : Disabled. Default Gateway : Default TTL : 64. Arp Age : 20. Domain Suffix : DNS server : | Proxy ARP.
  3. With multiple VLANs and some other features configured, showip. provides additional information:

How do I configure my HP switch interface?

To configure an Ethernet interface follow the steps given below:

  1. Enter system view and use the command.
  2. Enter Ethernet interface view and use the command.
  3. Set the interface description and use the command.
  4. Set the duplex mode of the interface and use the command.
  5. Set the port speed ans use the command.

Which command will change the CLI prompt?

set prompt command
Use the set prompt command to change the prompt for the CLI.

How do I create a VLAN on an HP switch?

Configuring basic VLAN settings

  1. Enter system view, use the command: system view.
  2. Create VLANs, use the command: vlan { vlan-id1 [ to vlan-id2 ] | all }
  3. Enter VLAN view, use the command: vlan vlan-id.
  4. Configure a name for the VLAN, use the command: name text.
  5. Configure the description of the VLAN, use the command:

How do I upload config files to HP switch?

To copy a configuration file from a USB device to the switch:

  1. Insert a USB device into the switch’s USB port.
  2. Execute the following command: HP Switch# copy usb startup-config HP Switch-config.
  3. At the prompt, press [Enter] to reboot the switch and implement the newly downloaded software.

How do I capture a running config in PuTTY?

Capture network device config with PuTTY

  1. Right-click the window title and choose “Change Settings…”;
  2. In the tree menu on the left, select “Logging” beneath “Session”;
  3. Select the “All session output”; radio button and choose a suitable destination file;

How do I debug my Aruba controller?

Debugging can be enabled for a particular client by using the ‘logging level debugging user-debug <user-mac-address>’command. The ‘show debug’ command can be used to view MAC addresses for which user-debug has been enabled. The ‘no logging level debugging user-debug <user-mac-address>’ command disables user debug.

How do you take console of Aruba AP?

To access the AP console command prompt, press Enter when the AP displays the message “Hit <Enter> to stop autoboot.” If the autoboot countdown expires before you can interrupt it, turn the device off and then back on.

Related Post