Does HP still make ProCurve switches?
HP ProCurve was the name of the networking division of Hewlett-Packard from 1998 to 2010 and associated with the products that it sold.
Is HP ProCurve a managed switch?
The HP ProCurve 1700 Switch series consists of two 10/100, fanless, web-managed switches that are ideal for open offices that require silent operation or businesses making the transition from unmanaged to managed networks.
What is the default IP of HP switch?
The HP ProCurve Switch 1700 Series has a default IP address of 192.168. 2.10 with a subnet mask of 255.255.
How do I connect my HP ProCurve Switch?
To connect a console to the switch, use the console cable shipped with the switch and connect a PC or VT-100 terminal to the console serial port. The PC or terminal then functions as a management console connected directly to the switch.
Do HP switches have a lifetime warranty?
HP is offering a lifetime warranty on the device, which the company defines this way: “For as long as a product is owned, with next-business-day advance replacement (available in most countries).” Switch owners will be entitled to “standard next business day advanced-replacement (availability varies by location) with …
What does a ProCurve switch do?
The HP ProCurve 1410-8G, 1410-16G, and 1410-24G Switches are multiport switches that can be used to build high-performance switched workgroup networks. These switches are store-and-forward devices that offer low latency for high-speed networking.
What does a ProCurve Switch do?
How do I find the IP address of my HP switch?
A switch should have a web interface and a telnet interface. Another approach would be to use the arp command to find its IP address from the Mac address (which should be physically labeled on it somewhere).
How do I configure my HP ProCurve Switch 2610 48?
- 1 Getting Started.
- 2 Selecting a Management Interface.
- 3 Using the Menu Interface.
- 4 Using the Command Line Interface (CLI)
- 5 Using the Web Browser Interface.
- 6 Switch Memory and Configuration.
- 7 Interface Access and System Information.
- 8 Configuring IP Addressing.
How do I reset my HP ProCurve switch 2510G 48?
Re: Reset and clear a HP ProCurve 2510G-48
Take a paper clip and bend the ends so the pointed tips form a Y. Push in the reset and clear at the same time. Then keep the clear pushed in and release pressure off the reset. Let it go through the power on self-test.
How do I configure my HP ProCurve switch 2610 48?
What is HPE parts Exchange support?
HPE Parts Exchange Service provides replacement parts that are either shipped to your location in advance of, or following your return of, defective parts to HPE. The service includes shipping charges for standard delivery, with options available for predetermined time and place of delivery and return pickup by HPE.
How do I configure my HP Procurve Switch 2610 48?
What is the default password for HP Procurve Switch?
In the factory default configuration, the switch has no IP (Internet Protocol)address and subnet mask, and no passwords.
How do you set up a ProCurve switch?
How to: Configure a HP ProCurve switch
- Step 1: Connect your serial connection.
- Step 2: Conenct PuTTY.
- Step 3: Get the IP address.
- Step 4: Set time server.
- Step 5: Set SNMP community info.
- Step 6: Launch the web GUI.
- Step 7: Configure basic info.
- Step 8: Create VLANs.
How do you find the IP of a switch you are connected to?
To determine the IP address, go to the Layer-3 device that you switch is connected to. In the Layer-3 device ( mostly a router or layer 2.5 switch ) run the “show ip arp” command. And there it is !
How do I configure ports on my HP switch?
Enabling or disabling ports and configuring port mode (CLI)
- You can configure one or more of the following port parameters.
- See Status and parameters for each port type.
- To configure port C5 for auto-10-100, enter this command: HP Switch(config)# int c5 speed-duplex auto-10-100.
What is Trk1 in HP switch?
Trk1 is a logical port and can be assigned to a Vlan as any other physical port. An IP address is assigned to Vlan 10 to test connectivity. vlan 10. untagged Trk1.
How do I reset my HP POE switch?
Solution:
- Using pointed objects, simultaneously press both the Reset and Clear buttons on the front of the switch. The power and fault lights come on.
- Continue to press the Clear button while releasing the Reset button.
- When the Self Test LED begins to blink, release the Clear button.
What is the default password for HP ProCurve switch?
What is the default username and password for HP switch?
The default username for first time configuration is admin, no password is required.
How do I configure my HP switch?
How do I reset my HP ProCurve Switch 2510G 48?
Do switches have IP addresses?
Unmanaged and layer 2 network switches do not have an IP address, whereas managed switches and layer 3 switches do. A network switch with an IP address is required for Telnet which allows remote access to the switch. The IP address of a switch can be found via the router or an IP scanner.
How do I enable ports on my HP?
Power on the laptop by pressing the button on the top of the dock. The light on the button will illuminate when powered on.