How do you remove a Yamaha impeller?
Okay with our pump out we can start to remove our impeller in order to do so we need to use our shaft holder tool that will allow us to place the shaft and our vise. And not damage the splines.
How do you change the impeller on a Yamaha 150 outboard?
From yamaha exactly the same. One exactly the same one. You see the notch here we’re gonna make sure that notch goes right into place it’s just a little difficult to put in work it down slowly.
When should I replace my Yamaha outboard impeller?
As a general rule, inspect the impeller and water pump assembly every year if operating in salt, brackish or turbid water, and replace if necessary.
How long do Yamaha impellers last?
All impellers should be changed at a minimum of three years.
How do you know if you have a bad impeller?
It’s usually pretty obvious to see wear and tear but look for cracks, bends, and melted rubber. Engine overheating. Make sure to check your temperature gauges often if you believe you have a bad impeller. 160°F (71°C) is the hottest gasoline engines should run.
Why is my impeller not pumping water?
Once the cooling system is full of water, with no outlet, the impeller just agitates it, without cooling the motor. The second is that the water inlets are clogged; no water is getting to the pump, so it isn’t pumping. Finally, the impeller may be damaged or worn beyond repair, requiring its replacement.
What happens when impeller goes bad?
If your impeller fails, the pump can’t pump cool water to the engine causing your engine to overheat. If you catch that your impeller is failing early on, you might avoid major problems. However, if you’re not fortunate enough to catch a bad impeller, the results can be catastrophic to your engine.
How can I tell if my impeller is bad?
Here’s a list of all of the signs that your impeller needs to be replaced.
- Impeller wear and tear.
- Engine overheating.
- Engine smoking.
- Reduction in engine pee.
- Engine sounds hollow.
- Impeller hasn’t been replaced in over 300 hours.
How do I know if my water pump impeller is bad?
These five signs can help you recognize that it’s time to bring your car in for inspection and possible water pump repair.
- Coolant Leaking. One of the first signs of a potentially faulty water pump is a puddle of coolant on the ground where you’ve parked your car.
- Rust or Deposit Build-Up.
- Noise.
- Overheating.
- Steam.
What causes boat impeller failure?
Abrasive sandlike material can cause the impeller to wear out faster. Impellers can also wear out by becoming stiff and brittle due to the motor sitting unused for several seasons or being exposed to heat. Water lubricates the impeller, and if it’s run dry, the impeller can be ruined in a few seconds.
What causes impeller to fail?
The top 3 most common causes of impeller failure are cavitation, erosion, and corrosion. Cavitation is a huge danger, and any centrifugal pump is cavitation. “The common cavitation phenomenon on the pump impeller is caused by the pressure difference on the pump body or the impeller.
What does a bad impeller sound like?
Rattling Noise
A rattling noise means one of two issues: Bad bearings. Bent or broken impeller shaft.
Why is my impeller not working?
How long does it take to change an impeller?
Changing an impeller, on many engines, usually takes less than 20 minutes even if you are fairly slow. The most complicated aspect of the task is physical access to the pump. Raw water impellers are a wear item unfortunately they do not always abide by a time or hours of use schedule.
What happens when an impeller fails?
What is signs of worn impeller?
What Indications Tell You That You Need to Replace the Impeller on an Outboard Boat Motor?
- The Maintenance Schedule.
- When the Outboard Shows Signs of Overheating.
- A Reduced Stream of Water at the Cooling Water Outlet.
- The Impeller Has Been In Service for Three Years.
How do I know if I need to replace my impeller?
Why is my impeller not spinning?
One of the most common causes of this phenomenon is due to debris blockages and obstructions. Weeds, waste products, stones, and other materials may have prevented them from functioning. And as the obstructions continue, the motor of the pump will just run even though the impellers do not spin anymore.
How do I know if my impeller is bad?
What happens if you put an impeller in backwards?
When the impeller rotates in reverse, fluid enters the eye of the impeller as normal. But instead of the impeller velocity forces flinging the water out of the impeller and into the volute, the impeller vanes cup the water and direct the flow in the opposite direction of the volute.
How do I know if my impeller is not working?
Ignore the symptoms of an impeller in need of replacement only if you wish to purchase a new motor.
- The Maintenance Schedule.
- When the Outboard Shows Signs of Overheating.
- A Reduced Stream of Water at the Cooling Water Outlet.
- The Impeller Has Been In Service for Three Years.
What are the signs of a bad impeller?
Ignore the symptoms of an impeller in need of replacement only if you wish to purchase a new motor.
- The Maintenance Schedule.
- When the Outboard Shows Signs of Overheating.
- A Reduced Stream of Water at the Cooling Water Outlet.
- The Impeller Has Been In Service for Three Years.
Should impeller spin freely?
It shouldn’t spin like a top but you should be able to rotate it 360 degrees smoothly with out it having any binding or sticky spots. It’s hard to describe the amount of force it should take to spin it but it shouldn’t be much.
How do you unclog an impeller?
Swimming Pool Service Tip: Unclogging Your Impeller – YouTube
Which direction does the impeller go?
How to Determine Impeller Rotation – YouTube