How do you use the XY mic?
XY Stereo
If you’re like most engineers, then the XY technique is probably the first stereo miking technique you learned. This one is extremely simple to set up — just position two cardioid mics (usually small-diaphragm condensers) at right angles, aligning the front of the capsules, and you’re good to go.
What mics are used in a typical X Y configuration?
X/Y uses two cardioid microphones in an X/Y fashion and also creates a stereo image, but doesn’t allow for additional control of it. The basic difference is that mid-side allows for greater stereo control.
What is an XY configuration?
XY stereo recording uses a coincident pair of directional- or bidirectional, angled microphones. Hence, the directional information is obtained solely from the level difference between signals. In practice, “coincident” means that the microphone capsules must be placed close and normally slightly above each other (fig.
How do I set up my ORTF mic?
ORTF Mic Placement
ORTF mic technique uses a “near-coincident” pair of cardioid microphones. Near-coincident means the mic capsules are reasonably close to each other. Alternatively, a coincident pair means the capsules are as close to each other as physically possible, such as in the X/Y mic technique.
How do you hook up a microphone to a stereo?
Stereo Mic Setup – Studio Recording – YouTube
What is good mic technique?
You should hold the microphone at a distance of 10-20 centimetres away from your mouth. You should hold it further away at a distance of up to 20cm when you sing higher or more powerful notes. If you move around and turn away from the stage always maintain the same distance.
How far apart should stereo mics be?
3 to 10 feet apart
If the microphones are too close together, there won’t be enough time differential between the two mics, and either no stereo image or a very narrow stereo image will be captured. In general, a distance of spacing the microphones 3 to 10 feet apart is enough to capture a nice, wide stereo image.
What is ORTF configuration?
ORTF combines both the volume difference provided as sound arrives on- and off-axis at two cardioid microphones spread to a 110° angle, as well as the timing difference as sound arrives at the two microphones spaced 17 cm apart.
Can I connect microphone to amplifier?
So yes, a microphone can often be plugged directly into a powered speaker amp and work just fine. To properly plug a microphone into a powered speaker, plug the microphone into the mic input of the speaker.
Can I connect microphone to Aux?
The Auxiliary input is designed for an amplified signal such as what is output from a smartphone headphone output. In order to use a microphone with the Aux input, it would need to be used with a microphone preamplifier before the signal gets to the Livemix Aux in.
Why do singers tap the mic?
Direct mouth-to-mic contact is done to increase the volume of the singer’s voice, as well as amplify low notes (this is called the proximity effect). It’s useful when there’s a lot of other onstage interference from loud instruments, other singers or even monitors.
Why do singers touch the mic with their lips?
The primary reason singers put their mouths directly on microphones is for an improved signal-to-noise ratio. By keeping the mic at the mouth, the microphone will effectively pick up more of the voice and less of the background instruments/noise, thereby improving vocal intelligibility.
Is a microphone mono or stereo?
Microphones convert sound waves to audio signals via mic capsules. Most mics have one capsule that outputs one signal, making them mono devices.
What is ORTF mic placement?
With ORTF, you have your mic capsules aimed with an exact 110 degree angle difference from each other. The mics must also be spaced exactly 17cm apart. Looking at a diagram of it, you can see that this setup approximates the positioning of ears on a human head (although, don’t confuse it with binaural recordings!).
Can a mic be connected directly to a speaker?
However, it is certainly possible to connect a microphone directly into a speaker. How to plug a microphone into a speaker: To plug a microphone into a speaker physically, we must identify the speaker input connector and then use the proper cable adapters to send the mic output signal to the speaker input.
What do I plug my microphone into?
Microphones will typically plug into one of the following:
- Microphone Preamplifier Input (Mixer, Recorder, Audio Interface)
- In-Line Device (Pad, HPF, Standalone Preamp)
- Audio Snake.
- Speaker Directly.
- Other Devices (Guitar/Bass Amp, Smartphone, Computer, Camera)
Can I plug a microphone directly into speakers?
Does chewing gum help singing?
Chewing gum could also help lubricate your vocal cords. Your mucous glands are active when you are chewing and in turn, your vocal cords get lubricated.
What microphone do most singers use?
SHURE BETA 58A DYNAMIC MICROPHONE
The Shure Beta 58A Dynamic Microphone is the industry standard professional microphone for live vocals, building on the immense success of its cheaper (but still just as widely used) brother the Shure SM-58.
Should vocals be stereo or mono?
mono
Should you record vocals in mono or in stereo? If you are recording the vocals of one singer in a booth, then you should record in mono. However, if you are recording vocals of multiple singers and instruments, you should record in stereo. The terms mono and stereo are quite common in the sound recording industry.
Do vocals have to be mono?
If you record one vocalist, your vocals should be mono. However, if you record two vocalists or more or if you record in a room with unique acoustics, the vocals should be stereo.
What’s the advantage of using the XY miking technique?
The downside is that you won’t get a lot of stereo width with this miking technique that is why it’s better for close mic applications. In short, the advantage of XY miking is that you’ll avoid timing differences in the signal being recorded by two mics.
Do microphones need amplifier?
Microphones Typically Plug Into Microphone Preamplifiers. Microphones output mic level signals. These mic level signals require amplification to become line level signals (for use in mixing boards, digital audio workstations, and audio recorders).
Where do I plug my microphone into?
On a desktop computer, the microphone jack is often on the back and identified by the pink color, as shown in the image. However, microphone jacks may also be on the top or front of the computer case. Many laptop computers and Chromebooks have a microphone built into them.