How many ml of Clonex is in a gallon of water?

How many ml of Clonex is in a gallon of water?

Mix 15 mL to a gallon and the cuts will be pretty happy.

How much Clonex should I use?

How to Use Clonex Clone Solution. Mix 5ml – 10ml of Clonex Clone Solution per liter of water (one or two teaspoons per quart). After mixing, adjust pH to appropriate level (5.5 to 6.5). Finally, soak medium for several hours or add to Aeroponic system.

How much is Clonex gel?

Compare with similar items

How do you use clone X gel?

First, dip cutting in gel to desired depth. Then insert cutting into rooting medium. Mist cuttings and place in propagator or a warm, clean, moist and humid environment. Finally, look for root development in 1 – 2 weeks.

How much is a Clonex clone solution per gallon?

2 1/2 tablespoons

For general use, dilute at a rate of 10ml (2 teaspoons) Clonex® Clone Solution per 1 liter (1 quart) of water or 2 1/2 tablespoons per gallon.

What is the best pH level for clones?

Clones do best in both coir and the plastic cubes at a pH of 6.3. Many people use Rockwool starter cubes for cloning. They are made from spun basalt rock.

How long does Clonex Gel last?

two years
Once opened, how long will Clonex gel remain effective? Clonex gel is guaranteed for two years but, the effectiveness will be shortened if best practices are not followed.

Can you mix Clonex Gel with water?

Mix 5ml – 10ml of Clonex Clone Solution per liter of water (one or two teaspoons per quart). After mixing, adjust pH to appropriate level (5.5 to 6.5). Finally, soak medium for several hours or add to Aeroponic system. Allow for adequate drainage to avoid water logging.

Is rooting gel better than powder?

Growers experience faster root initiation when using Hormex Rooting Powder compared with a root hormone gel. One aspect of cloning that is often overlooked is the speed at which the cuttings root.

Is Clonex a good rooting hormone?

100% rooting success using the clonex gel. Good consistency gel sticks to base of cutting well and wont let you down with the rooting results. Been using it for years with no problems. Highly recommended.

Can you mix Clonex gel with water?

What should my pH be for clones?

Clones do best in both coir and the plastic cubes at a pH of 6.3. Many people use Rockwool starter cubes for cloning.

What should I put in my cloner water?

Adding 1/4 -1/2 strength bloom nutrients (200–600 ppm or EC: 0.4–1.2) to the cloner improves rooting both in speed and volume. We recommend nutrients intended for water culture. Avoid products which will inoculate or feed bacteria and fungi such as amino acids, protein hydrolysates, sugars, carbohydrates, or ‘teas’.

Do clones need pH water?

Water should be between 5.8 and 6.3 measured pH. 3. 3. Taking the cuttings: Create cuttings by taking them from the top of the plant were the most growth occurs.

What pH is tap water?

between 6.5 and 8.5
EPA guidelines state that the pH of tap water should be between 6.5 and 8.5. Still, tap water in the U.S. tends to fall below that — in the 4.3 to 5.3 range — depending on where you live.

How long does Clonex take to root?

Finally, look for root development in 1 – 2 weeks. As a matter of fact, you can use Clonex Rooting Gel on all types of plant cuttings, including woody, herbaceous, and flowering ornamental species, vegetables, fruit trees and small fruits.

How long is cloning gel good for?

How long is Clonex Gel effective once it’s been opened? Clonex Gel is guaranteed for two years if best practices are followed. Best practices include not dipping directly in the Clonex bottle and storing your Clonex in the refrigerator when it’s not in use.

How long till my clones grow roots?

seven to 10 days
After seven to 10 days, clones usually begin to show roots. Some plant varieties take longer and some don’t take as long. Once clones are rooted and acclimated to the ambient humidity and temperature, they can be treated as vegetative plants.

Can you use too much rooting hormone?

Dip the end of your cutting into a cup or bowl containing the hormone. Only hold the cutting there for a second or two, not more. Too much time can cause the plant to absorb too much rooting hormone, which may cause the leaves to yellow or burn the plant stem.

Is rooting gel necessary?

“Rooting hormone can help yield better results, but it’s not necessary.” Plants that easily propagate, such as most varieties of succulents, rarely need the jumpstart that a rooting hormone can deliver. However, plants that are more reluctant to root, such as citrus plants, can benefit from it.

Do you have to pH water for clones?

How often should I change Cloner water?

– Change the water and solution in your cloning machine every 5 days. This keeps your solution fresh and helps prevent the growth/build up of pathogens.

Should I put nutrients in my cloner?

Freshly cut clones have no roots with which to take up nutrients, so feeding is not required until the first young roots have formed and then nutrients should be first applied at quarter strength, increasing to half vegetative strength as the clones become more developed.

How often should I change the water in my cloner?

Do clones need 24 hrs of light?

The light cycle for clones is best handled at 18 hours on, 6 hours off. In some cases growers use a 24 hour light cycle during cloning.