What does it mean when ecobee sensor says occupied?
If an Ecobee sensor is occupied, this means that movement was detected within the range of the sensor. Ecobee sensor occupancy detention is used in the three smart modes: Follow Me mode. Smart Home mode.
How long does ecobee sensor stay occupied?
Follow Me includes participating sensors that have detected occupancy within the past 30 minutes. If you leave a room and its sensor stops detecting motion, that sensor’s temperature readings will be gradually (not immediately) removed from your ecobee’s setpoint calculation over a 30-minute period.
How do I make my ecobee sensor occupied?
Tap and hold your finger on the number to the right and drag it to set the desired indoor temperature that you want your thermostat set at when you’re not at home. Then hit “Save” in the bottom-right corner. Do the same thing for the heating temperature if you have the heat running.
How do I reset my ecobee door sensor?
1 Factory Reset
- Remove the circular backing from the back of the sensor.
- Remove the battery from the battery slot.
- Gently lift the prongs in the middle of the battery slot with your index fingernail.
- Place the battery back into the battery slot with the positive side facing down for 30 seconds.
How does ecobee sensor detect occupancy?
They use the motion and temperature of moving objects to determine if the room is empty or occupied. Smart sensors can also send you a reading of your room’s temperature on any device and your thermostat. Smart sensors detect movement farther away than room sensors.
Why is my ecobee sensor not working?
If your SmartSensor isn’t pairing, please try the following steps: Flip the battery from the SmartSensor + side down and leave it in the sensor for two minutes. Power-cycle the ecobee by removing it from the wall and leaving it off for about two minutes. Restart your smartphone.
How do the ecobee remote sensors work?
The remote sensors do not include a humidity sensor, but the ecobee does. The motion sensors are passive infrared motion sensors. This means they use the natural infrared radiation given off by all objects as a means of detecting motion, and therefore work regardless of light or dark.
How often do ecobee Smart sensors update?
How Often Do ecobee Sensors Update? One of the key features of the ecobee sensors is their accuracy during real-time monitoring of your home. The sensors will update their temperature reading every 15 seconds.
Why is my ecobee sensor not pairing?
How do I recalibrate my ecobee room sensor?
Remove the back cover from the sensor and remove its battery. Power-cycle your ecobee thermostat by removing it from the wall and leaving it off for about two minutes. Place your ecobee thermostat back on the wall and wait for it to power up. Re-insert the battery into your Room Sensor and hold it close to your ecobee.
How accurate are ecobee sensors?
The ecobee temperature sensor has a +/- 1.0F accuracy and is programmed to provide readings every 15 seconds. It will use the previous two values and average them into the current reading.
How often do ecobee sensors update?
Is there a battery in the Ecobee thermostat?
Your ecobee room sensor is powered by a single 3 Volt CR-2032 battery.
How do I know if my ecobee sensor is working?
1) Gently pull the plastic tab on the back of the sensor. 2) Look for a message on your ecobee’s screen. The 4-digit ID should match the 4-digit code on the back of your sensor. Tap Pair now to confirm pairing.
How do I calibrate my ecobee sensor?
1 Temperature Correction
- Press Menu on the main screen.
- Go to Settings.
- Then go to Installation Settings.
- Select Thresholds.
- Then select Temperature Correction.
- Adjust the temperature reading to fit your needs.
How does Ecobee sensor detect occupancy?
How do I reconnect my ecobee room sensor?
How to Re-Pair Ecobee 3 Room Sensor – YouTube
How often should ecobee calibrate?
The “Calibrating” message on your Ecobee thermostat screen indicates that it is measuring the current indoor temperature. Ecobee calibrates once it’s installed initially or when it reboots, and it typically takes around 5 to 20 minutes. What is this?
Why is my Ecobee sensor not connecting?
How do I change the battery in my ecobee sensor?
How To Change The Ecobee Sensor Battery – YouTube
Why is my ecobee sensor not connecting?
Can ecobee sensors be calibrated?
Calibration helps your Ecobee thermostat get an accurate reading of the temperature inside your house or office. The Ecobee uses its built-in sensors to measure the temperature, which also helps it to measure humidity and room occupancy.
Why won’t my ecobee sensor connect?
A sensor could lose connection from your ecobee thermostat if: The battery is low. It’s too far from your ecobee (more than 45 feet). There’s interference from environmental factors (walls, or other devices broadcasting on the same 915MHz frequency, such as a baby monitor, cordless phone, etc.)
How do you force ecobee to calibrate?
Is there a way to calibrate my Ecobee Thermostat?
- To configure temperature correction.
- First, the menu button on the main screen.
- Go to setting.
- Then go to installation settings.
- Select threshold.
- Then select Temperature Correction.
- Adjust the temperature reading according to your needs.
Why does ecobee take so long to calibrate?
“Calibrating” means that the Ecobee thermostat sensor is measuring the current indoor temperature. This process takes 5-20 minutes. Ecobee calibrates after it’s initially installed and any time it reboots.