How do I restart my apc Network Management Card?
1.) Hold down the Reset button for 20-25 seconds, ensuring the Status LED is pulsing green during this time. 2.) When the Status LED change to amber or orange, release the Reset button to allow the NMC to complete its reboot process.
How do I restart my apc NMC?
Solution: To reset the network interface of a SMT, SMTL, or SMX model UPS, on the display interface hold the UP and DOWN buttons simultaneously for 5 seconds.
How do I reset my apc Network Management password?
Press the Reset button a second time immediately while the LED is flashing to reset the user name and password to their defaults temporarily. 6. Press ENTER, repeatedly if necessary, to display the User Name prompt again, then use the default, apc, for the user name and password.
What is the default IP for apc Network Management Card?
The default IP address is 192.168. 2.66 with a subnet mask of 255.255. 255.0. The default username is admin and the default password is admin01.
How do I reset my network management card for UPS?
Press and hold the NMC’s pinhole reset button for 20+ seconds, ensuring the NMC’s status LED is pulsing green during this time. When it changes to amber or orange, release the reset button to let the format function complete and for the NMC to complete its reboot process.
How do I reset my UPS management card?
Locate the APC network management interface on the back of your APC UPS. Press the reset button for 20 seconds. Wait for the network led change to the orange color. The APC UPS network management interface will reset its configuration back to the factory default.
How do I reset my UPS NIC?
How do I configure apc Network Management Card network settings?
Connect to the UPS/device serial port using the correct APC configuration cable.
…
9600 bps, 8 data bits, no parity, 1 stop bit, and no flow control.
- Apply the port settings to establish the connection.
- Press enter 3-5 times to display the username prompt.
- Use the default username and password of “apc”.
What is UPS network management card?
APC UPS Network Management Cards allow for secure monitoring and control of an individual APC UPS via web browser, command line interface, or SNMP. The configurable notification features keep you informed of problems as they occur.
How do I setup my apc network card?
How do I reset my ups?
To do this, follow the below procedure;
- Disconnect any attached load.
- Unplug the UPS from the wall socket.
- Disconnect the UPS’ internal battery or the battery disconnect switch if any.
- Push and hold the “”On”” button on the UPS for 5 seconds.
- Reconnect internal battery or battery disconnect switch if any.
How do I factory reset my ap9631 network management card?
Hold the reset button for 5-7 seconds. Resets only the password. Hold the reset button for 20 seconds. This will restore the card to factory default settings including switching back to DHCP mode.
How do I reset my Eaton UPS network management card?
Type 0 and press Enter to return to the Network Card-MS main menu. 6. From the main menu, type 1 for the Reset menu and press Enter to save this new configuration. Type 1 again and press Enter to Restart the card from the boot.
How do I reset my ap9630?
Why my UPS is not working?
Be sure the line cord is connected. Be sure each circuit breaker is in the On position, or replace the fuse if needed. If this occurs repeatedly, contact an authorized service provider. Check the UPS LEDs to be sure a battery or site wiring problem has not occurred.
What is the use of reset button in UPS?
Those are circuit breakers. If one of the circuits were to be tripped, that button would be sticking out significantly farther than normal and would need to be pushed back in to reset the circuit.
How do I reset my ups NIC?
Press the reset button for 20 seconds. Wait for the network led change to the orange color. The APC UPS network management interface will reset its configuration back to the factory default.
What is the default password for APC UPS?
The default username for your APC UPS is apc. The default password is apc. Enter the username & password, hit “Enter” and now you should see the control panel of your router.
How do I reset UPS?
Turn off the UPS: press and hold the On/Off button until the UPS beeps, then release the button. Disconnect the UPS from the AC outlet. 3. Reconnect the UPS to a functioning AC outlet.
What is the life expectancy of a UPS?
Some UPS systems may normally last up to 13 years or more before they need to be replaced. However, its critical components are subject to failure far earlier than the UPS itself.
How do I reset my UPS?
How do you hard reset a UPS?
The Brain Dead procedure performs a hard reset of the Smart-Ups microprocessor.
Cold Start:
- Turn off and unplug the Smart-UPS from wall.
- Press and hold the power button (labeled “”I/TEST”” on legacy non-LCD screen units) on the front of the UPS until you hear a LONG beep.
- Let go DURING the long beep.
How do I reset my ap9631 network management card?
Should I keep my UPS plugged in all the time?
Should I Keep My UPS Plugged in at All Times? Yes, your UPS devices should always remain connected to grid power. If you experience bad power quality or a power outage, it can happen so suddenly that you may not have time to plug the ups in and switch it on.
When should I replace my UPS?
But, with proper servicing, a UPS can operate safely and reliably. If it’s under 12 years old, you probably have a little life left. If it’s over 12 years old, it may be time to replace the system.