How do I winterize my Ice-O-Matic ice machine?
During the winterization service, the tech will complete the following:
- Shut down the ice machine.
- Empty the ice bin.
- Disconnect and drain the water lines.
- Remove the water filter(s).
- Drain the housing and any reservoirs.
- Blow out the water-cooled condenser (if applicable to the ice maker).
How do I read my Ice-O-Matic model number?
Machines manufactured in 2004 or later have a 14 digit SN the first two digits indicate the year of manufacture the second two indicates the month. Machines prior to 2004 have a SN that begins with a letter followed by 8 digits A=Jan B= Feb, etc. The number that follows is the year 0=2000 1=2001.
Why is my Ice-O-Matic ice machine blinking red?
Ice-o-Matic says a flashing red light signals a thermistor failure. The thermistor is a temperature-sensitive resistor that measures temperature. It works hand-in-hand with the temperature controller. Malfunctions regarding temperature can prevent ice machines from making ice.
How do I clean my Ice-O-Matic gemu090 machine?
Using a soft cloth or soft-bristled brush, wash all interior ice bin surfaces including the door, interior walls, door track, and drain. Allow the bin to soak for 15 minutes to allow the solution to loosen any mineral deposits within the bin. Wash the interior surfaces again to remove stubborn deposits.
Where is the reset button on a ice O Matic ice machine?
How to Reset and Restart an Ice-O-Matic Ice Machine
- Loosen the two screws at the base of the front panel with a Phillips head screwdriver.
- Lift the front panel up and then off of the unit.
- Press and hold both the Power Button and the Clean Button for 3 seconds to turn the machine off.
How do you adjust the ice thickness on an ice O Matic ice maker?
The ice thickness can be changed on the Float Housing by turning the adjustment clockwise to decrease the bridge thickness and counter-clockwise to increase the bridge thickness. You will hear a “click” with each adjustment. it is recommended adjustments be made one or two “clicks” at a time.
Where is the reset button on an ice O Matic ice machine?
Resetting and Restarting an Ice O Matic Elevation Series Machine 1
How old is my ice machine?
To find the date the unit was manufactured, look on the data plate for a box that contains MF DT or MFG DT (manufactured date) followed by four numbers. The first two numbers are the year, followed by two digits representing the month.
Why is my ice maker light blinking?
If the green power light on the icemaker is blinking, ice cubes may be stuck in the icemaker.
How do I clean my ice maker?
How to Clean a Commercial Ice Machine – YouTube
How do you troubleshoot ice O Matic?
If your Ice-O-Matic ice machine is running but not making ice, here are a few things to check out to diagnose the issue.
- Is there water leaking out of the purge drain or water trough?
- Is the compressor running?
- Is the condenser dirty?
- Is the hot gas valve leaking during freeze cycle?
Will unplugging my fridge reset the ice maker?
This will force the ice maker to run water and begin the process of creating ice. For models that have an on/off switch, you should turn the switch off and unplug the refrigerator. Leave the refrigerator unplugged for 5 minutes. This will allow the ice system to reset.
Why is my ice machine making thick ice?
Moving the sensor further away from the grid creates thicker ice, while moving it closer creates thinner ice. Be careful, though, as making the ice too thin can cause it to shatter before it can be used, while too thick of a bridge can produce sheets of ice that won’t break apart.
Why is my ice machine making thin ice?
A clogged or incorrectly installed water filter will reduce the water flow to the ice maker, which will result in thin ice cubes or low ice production.
Why did my ice maker stop working?
A clog, leak, or damage in the water line may cause the ice maker to shut off automatically or otherwise stop working. Check the ice maker inlet valve and water supply tubing for any leaks, damage, or blockages.
Where is the model number on my ice maker?
Ice Machine– How to Find the Model Number – YouTube
Why is my Manitowoc ice machine not making ice?
Not Making Ice or Making Low Amount of Ice
Make sure the water service valve is open. Water float valve – See if the water float valve and its filter screen are dirty. Either can cause low ice capacity. Condenser is dirty – Make sure the condenser is clean and free of obstructions, especially in air-cooled models.
What would make my ice maker stop working?
Why did my ice maker quit making ice?
If your ice maker isn’t producing ice at all or is producing crescents or cubes that are smaller than usual, it’s typically indicative of a clog somewhere along the supply line. Cause: A common cause for a clog is frozen water in the line. Fix: To repair a frozen line, slide the refrigerator and unplug it.
Can I run vinegar through my ice maker?
If you don’t have affresh® ice machine cleaner at home, cleaning your ice machine with vinegar is another option. Make a mix of 10 parts water to one part distilled white vinegar and pour this into the water reservoir.
How often should an ice machine be cleaned?
once every six months
Your ice machine should be cleaned and sanitized at least once every six months for efficient operation. This maintenance process requires you to first perform a cleaning procedure to remove lime, scale, and mineral deposits, followed by a sanitizing procedure to disinfect the unit and remove algae and slime.
Where is reset button on ice maker?
The reset button is usually located at the bottom of the ice maker unit or in some cases at the top or on the bottom of the ice tray. Once located, press the button down for a few seconds until you hear a beep sound. Once you hear the beep sound, let go of the button. Once reset, check if the problem has been solved.
What causes ice maker to stop working?
How do I adjust the water flow on my ice maker?
Ice Maker Troubleshooting and Adjusting – Cube Size – YouTube
Why is my ice coming out in chunks?
When the ice bin is full, the pressure from the weight of the cubes can cause the bottom cubes to fuse and clump. To prevent this from happening, discard the clumped ice and check the bin periodically to ensure the ice is not building up.