How do you read Hotpoint error codes?
So if your appliance doesn’t have a display simply match up your flashing lights with the ones on the website to work out which error codes you have.
Is there a problem with Hotpoint washing machines?
About 20% of the Hotpoint and Indesit washing machines sold since 2014 are affected by a safety fault and need to be recalled, a process that started in January. Seventy-nine fires are thought to have been caused by an overheating door locking system, a fault that develops over time, according to Whirlpool.
Why are the lights on my Hotpoint washing machine flashing?
Pre wash light flashing
Indicates that the Hotpoint washing machine is failing to fill correctly. Check your fill hoses to make sure they are turned on correctly. It is also worth checking for any blockages, leaks or kinks in the fill hose pipe.
How do I reset my Hotpoint washing machine?
The machine gives you 30 seconds to lift the lid and close. It six times and once you start lifting the lid. You have 12 seconds to do the six repetitions.
What does it mean when all lights are flashing on washing machine?
If the wash, rinse and spin function lights all flash at the same time, this would indicate a possible blockage in your filter or waste / drain pipe.
Why is my washing machine showing error?
Common appliance codes could be related to a problem with the door, a water heating sensor, a software or circuit board fault, a motor or pump fault plus much more. Simple things that could have an error code could be the door being left ajar on the machine or the detergent drawer not in situ properly.
Why won’t my Hotpoint washer spin and drain?
If the washer won’t drain or is not draining properly, and the washer has a coin trap, remove the coin trap and clean it thoroughly. First, check the drain hose to determine if it is kinked, twisted, or bent. If the drain hose is bent, straighten it out. In addition, remove the drain hose and check it for obstructions.
Why is my Hotpoint washing machine not starting?
If the electrical outlet is receiving power, but the washer won’t start, the power cord might be defective. However, this is very rare. To determine if the power cord is defective, use a multimeter to test it for the cord for power. If the power cord is not getting power, replace it.
Why does my washing machine keep flashing?
If your washing machine detects an unbalanced or excessive wash load this will cause the spin light to flash. New machines will try to redistribute the load – but you may have to do this manually.
What does a flashing wash light mean?
The Wash Light is On or Flashing when the water level does not change for a period of time OR water is present but the control does not detect the water level changing.
What are common problems with washing machines?
10 Most Common Washing Machine Problems
- It Bounces Around.
- It’s Noisy.
- Clothes Are Getting Ripped.
- Improper Or Slow Draining.
- My Washing Machine Won’t Spin.
- There’s No Water.
- The Door Won’t Open.
- It’s Smelly.
Is there a reset button on a washing machine?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. Causes that lead to these problems include power spikes, imbalanced loads or an interruption in power. Some machines have a button you push to reset its motor.
How do you unblock a washing machine drain?
Washer Repair: How to Unclog the Drain Hose – YouTube
Why is my Hotpoint Aquarius washing machine flashing?
The end light is flashing
The end light flashes when the washing machine has been paused. Hopefully pressing start/cancel should get it running again. If not try cancelling the program and starting again.
How do you diagnose a washing machine problem?
Washer Troubleshooting Guide
- Check that the washer is plugged in securely.
- Check the circuit breaker or fuse box.
- Test the outlet for current.
- Check that the water supply valves are turned on.
- Inspect the filter screens.
- Test for overheating.
- Test the water level switch.
- Test the timer control.
How do I drain the water from my washing machine?
How to Drain the Water Out of Your Washing Machine – YouTube
How do you put a Hotpoint washing machine in diagnostic mode?
How to Diagnose and Repair a Hotpoint or GE Washing Machine
How do you fix a washer that won’t spin?
How To Fix A Washer That Won’t Spin
- Lighten the load inside the washer.
- Rebalance the load in the washing machine.
- Check or repair the washing machine drain hose.
- Check for blown fuses.
- Check the washing machine lid safety switch.
- Replace the drive belt in your washing machine.
- Replace the motor in your washing machine.
Why does my washing machine turn on but wont start?
Top-Load Washer Won’t Start — Washing Machine Troubleshooting
Why washing machine suddenly stopped working?
There are a few possible reasons for this: – The locking mechanism could have jammed (maybe some clothes have gotten in the way). – There could be a glitch in the washer’s computer. – The washing machine may not be draining properly, leaving the washer door locked and the drum filled with water.
How do you clear a clogged washing machine?
How to unblock Your Washing Machine (8 Easy Steps):
- Turn your washing machine off at the plug.
- Locate the pump filter.
- Place a bucket, towel or even a baking tray under the pump filter.
- Unscrew the pump filter SLOWLY.
- Wait for the water to finish draining.
- Check to see if there is a block.
Why is my washer blinking on wash?
Why is my washing machine flashing wash and rinse?
It’s either low water pressure, a clog somewhere in the line, a water inlet problem, or plugged filter screens. Of all those problems, appliance service technicians say the most common issue is a plugged, or dirty filter screen.
How many years should a washing machine last?
10 to 13 years
The average life of a washing machine ranges from 10 to 13 years, although some brands can manufacture washing machines with an even longer lifespan than the average appliance.
Can you hard reset a washing machine?
Reset your washing machine
There really isn’t a way to reset the washing machine. What you can do instead is power cycle it: Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again.