How much power does a 4 pin Molex put out?

How much power does a 4 pin Molex put out?

The ATX standard for SATA or Molex connections is rated for 54 watts. Each SATA/Molex connector provides three 12v pins at 1.5 amps each, for a total of 4.5 amps. 12 volts, times 4.5 amps, equals 54 watts able to be provided by a SATA/Molex connector.

What are Molex 4 pin connectors for?

Often refers to the 4-pin connectors used to attach DC power to the drives inside a PC cabinet. Molex is a large manufacturer of electronics plugs and sockets that dates back to the 1940s.

What color are the 4 wires on the Molex?

Molex diagram

Is IDE and Molex the same?

Yes, they are the same thing.

Is it safe to power PCIe riser with Molex?

If you have the ability to use MOLEX or PCIe power connectors, then you should use them. Using MOLEX or PCIe power connectors is definitely safer than using SATA power connectors as SATA was not made for higher workloads. Only use SATA with GPUs that draw less power via PCIe x16 slot.

How many volts is a 4-pin power supply?

+12 VDC

The ATX 4-pin power supply connector is a standard motherboard power connector used to provide +12 VDC to the processor voltage regulator.

What replaced Molex?

During the 90s, the Molex compound was phased out in connector housings, replaced by other thermoset plastic material, and eventually more environmentally friendly, recyclable thermoplastic materials.

Are Molex connectors still used?

Certain Molex connectors are used for providing power to the motherboard, fans, floppy disk drive, CD/DVD drive, video card, some older hard drive models, and more. Compatible connectors are available from many manufacturers, not just Molex and AMP.

Are all Molex connectors the same?

There are three typical pin sizes: 1.57 mm (0.062 in), 2.13 mm (0.084 in), and 2.36 mm (0.093 in). The 1.57 mm pin can carry 5 A of current, while the 2.36 mm can carry 8.5 A. Because the pins have a large contact surface area and fit tightly, these connectors are typically used for power.

Can you daisy chain Molex connectors?

you should have no problems at all with just 4. This vary’s I believe depending if you are daisy chaining directly to the PSU or to a motherboard fan header.

Is it safe to use SATA to Molex?

Molex to SATA adapter cables are a very simple and cost-effective alternative to buying a new power supply. However, they can be a dangerous alternative to getting a quality power supply, potentially damaging your SSD, internal components, and may also pose a fire risk in your home.

Does Molex carry more power than SATA?

Technically Molex can carry much more power than the SATA power connector. Molex has 2 power pins (one 5V and on 12V pin), each can deliver 11Amps for a total of 22Amps. The other 2 pins are ground wires… SATA power connectors has a total of 15 pins of which 9 are power pins (3 x 3.3V, 3 x 5V, 3 x 12V).

Should I use Molex to power GPU riser?

We suggest using MOLEX or PCIe 6 pin power connectors if possible. Only use SATA connectors on less power demanding GPUs like GTX 1060 6GB and if there is no other option available.

Is Molex better than SATA?

What is the voltage for 4 pin Molex connector?

Standard 4-pin Molex connectors coming from a PSU supply ~12v on the yellow wire, and ~5v on the red wire.

How many watts is a 4 pin connector?

4 pin peripheral power cable

Why do we still have Molex connectors?

Is it safe to convert Molex to SATA?

Why is it called Molex?

The name comes from the Molex Connector Company, which pioneered the two-piece electrical connectors that became standard in computers and other electronics.

How do you make a 4 pin Molex connector?

Assembling a Molex Connector – YouTube

What are the different types of Molex connectors?

Can you stack Molex connectors?

It will be fine.

How many fans can a daisy Molex chain?

Distinguished. you should have no problems at all with just 4. This vary’s I believe depending if you are daisy chaining directly to the PSU or to a motherboard fan header.

Can you power a hard drive with Molex?

Another option is to use a molex to SATA adapter cable. By going this route, you won’t need to worry about swapping out your power supply. Instead, all you need to do is plug the adapter into your PSU. Then plug your hard drive into the other end, and you’re good to go.

Can I power risers with Molex?

There are three regularly used power connectors that miners use to power riser cables: SATA. MOLEX. PCIe 6+2.