Is thru hull or transom mount transducer better?
Transom mounts are generally easier and cheaper to install. They suit tinnies and trailerable fibreglass boats, but work best in calmer waters. They are not recommended for operation at high speeds. In-Hull Transducers handle high speeds much better.
Can you use a transom mount transducer in hull?
The one in the fishfinder box was a simple transom mount and these units work perfectly well mounted inside the hull unless you have something fancy like Structure Scan or Side Scan.
Are through hull transducers any good?
Through-hull with fairing blocks offer the best performance, especially at higher speeds. Through-hull flush mounts are best for trailer boats where good performance is required and there are no protrusions from the hull. In-hull transducers do not penetrate the hull, but do sacrifice some performance.
Do in hull transducers work?
They can be a high performance option for certain fishing boats. Large high speed center consoles benefit from a smooth running surface.
Can a transducer read through fiberglass hull?
Can I mount my transducer inside the hull? The standard (83/200 kHz) pod style transducer and standard (83/200 kHz) skimmer transducer, have a proven track record of performing well shooting through a fiberglass hull when installed correctly. You will lose 10-15% of sonar performance when shooting through fiberglass.
Can you use a thru hull transducer on an aluminum boat?
A true thru hull transducer is one that you drill a hole for, and mount thru the hull. Those work fine on aluminum boats.
Can you mount a Garmin transducer inside the hull?
How to Install a in Hull Garmin Transducer (GT8HW-IH) – YouTube
What do you fill a hull transducer with?
water
Place the transducer inside a thin plastic bag partially filled with water and cinched tightly with a cable tie. Wet the mounting surface and press the active face of the transducer against the hull. Compare the bottom return to the baseline, and if the reading is similar, the mounting location is good.
Do you need a thru hull transducer?
Should I Use an in-Hull, Thru-Hull or Transom Mount Transducer With …
Can I glue my transducer inside the hull?
The most important thing to keep in mind is that transducers can only be glued inside hulls that are SOLID fiberglass or up to 1/8th” aluminum. However, since boat hulls absorb acoustic energy, transmitting through the hull reduces the transducers performance.
How far should a transducer be in the water?
The transducer should be even with the bottom of the boat or slightly below the bottom. Leading edge (the edge closest to the transom of the boat). One click too high: the transducer is tilted out of the water and cannot maintain a sonar signal.
How far below boat should Garmin transducer be?
The transducer should extend 3.5 mm (0.125 in.) below a fiberglass hull or 10 mm (0.375 in.) below an aluminum hull . On boats with outboard or inboard/outboard motors, the transducer should be mounted as close to the centerline of the transom as possible but at least 38 cm (15 in.)
How far away from motor should transducer be?
The ideal mounting location on a boat powered by an outboard or an I/O engine is about 18-24 inches starboard of the engine’s lower unit. If the boat has inboard power, mount the transducer far enough to starboard to clear any propeller turbulence.
Can a transducer be too deep?
Because the transducer can only ping in water so you do want it submerged. If it’s too deep sometimes the front face of it will create turbulence and bubbles = bad. Plus it can throw water up over your motor and inside your cowling resulting in saltwater intrusion.
What happens if transducer is too low?
A transducer placed too low in the water will cause water to flow over the top of the transducer creating a rooster tail and creating air bubbles that will travel over the bottom of the transducer.
How far below the transom Should a transducer be?
You want to have the leading edge of the transducer no more than 1/8” below the transom as a starting point.
How far below the hull Should a transducer be?
You should mount your transom-mount transducer parallel to the waterline. While the vessel is moving, the device should extend into the water 3.5 mm (0.125 in.) below a fiberglass hull or 10 mm (0.375 in.) below an aluminum hull.
Should my transducer be below the hull?
The transducer must be level with the bottom of the hull to ensure accurate depth readings. You can use the following tips to make sure your boat is level when out of the water.
Should transducer be even with bottom of boat?
Mounting Angle
The transducer should be even with the bottom of the boat or slightly below the bottom. Leading edge (the edge closest to the transom of the boat). One click too high: the transducer is tilted out of the water and cannot maintain a sonar signal.