What does the Audiocontrol LC2i do?
The LC2i, is a compact, two-channel processor with active input circuitry, which allows it to accept speaker-level signals of up to 400 watts per channel from factory-installed source units or amplifiers.
Where is Audiocontrol located?
The company’s headquarters, including research and development, manufacturing, production, and training facilities continue to thrive in Mountlake Terrace, Washington; heart of the rainforest of the Pacific Northwest.
Can the LC2i run 2 amps?
Registered. Yes, for the amp you can just connect it to the LC2 for the input. since you already spliced into front speakers for an input you’ll get audio from Bluetooth calls (again audio from Bluetooth only comes out of front stock speakers).
Does LC2i need a fuse?
The LC2i requires a +12V in order to run properly. For best results, the +12V should be provided by the battery via direct line or from a power distro-block. The preferred wire gauge for the connection is a 18 AWG, and a 1A fuse is recommended.
Is AudioControl Made in USA?
All AudioControl products are designed and manufactured at our factory located in the Pacific Northwest, USA..
What is a preamp processor?
Preamplifiers or processors are the brains behind any mid to high-end home theater system. They’re similar to AV receivers in that they provide source switching and decoding of all the various surround sound formats, audio/video processing, and volume control.
How do I tune my LC2i?
LC2i Training Video – YouTube
Does LC2i need power?
Adding Basic Power
The LC2i requires a +12V in order to run properly. For best results, the +12V should be provided by the battery via direct line or from a power distro-block. The preferred wire gauge for the connection is a 18 AWG, and a 1A fuse is recommended.
Where are AudioControl amplifiers made?
Seattle, WA
Engineered and manufactured in Seattle, WA, the GaN audio amplifier platform and CM Series 70-volt Dual-Mode amplifiers are further examples of a best-in-class, innovative product design from AudioControl. GaN-powered AudioControl CM Series amplifiers are available now.
Who bought AudioControl?
AAMP Global
Clearwater, FL (April 1, 2022) – AAMP Global, leading designer and manufacturer of vehicle solutions, has acquired AudioControl, known worldwide for high-performance audio solutions engineered for the automotive, residential, and commercial markets.
Does a preamp improve sound quality?
The sound contribution of preamps is not so much in its frequency response but in the texture it imparts on the sound. However, a preamp shapes the sound to a much lesser degree than one would think. Usually, its sound character only becomes obvious at high gain settings or when you drive it into distortion.
When would you use a preamp?
The purpose of a preamp is to amplify low level signals to line level, i.e. the “standard” operating level of your recording gear. Microphone signals are usually way below the nominal operating level, so a lot of gain is required, usually around 30-60 dB, sometimes even more.
Can I run 2 amps from an LC2i?
Yes. You can run rca cables for “main” output and for “bass” output. Mains would be to the amp you use for your door speakers and bass is obviously to the amp for your sub. Fade loss depends on how you hook up the wire inputs on the lc2i unit.
How do I stop my amp from getting hot?
First, try adding some ventilation near your amplifier. If there is a problem with the position of the amp, place it somewhere else. If it’s in a spot where it can be ventilated but you still have an overheating problem, you can mount a cooling fan to facilitate air flow.
Can I power LC2i from amp?
YES! By using the ‘Remote Out’ the LC2i can trigger up to 2 devices down the signal chain. This includes amps, line drivers, crossovers, etc… Anything with a remote in, the LC2i can trigger on when the unit turns on (whether it be GTO, or Remote).
When did AudioControl start?
1977
AudioControl is a leading designer and manufacturer of innovative high-performance audio solutions for the residential, commercial, and automotive markets since 1977.
How do I know if I need a preamp?
To check if a receiver has a built-in preamp, check if the receiver has a PHONO input. A receiver with a PHONO input definitely has a built-in preamp. If your receiver has a PHONO input, you can connect a turntable without a phono preamp to that input. This way, you will use the preamp that is built into the receiver.
Do I really need a preamp?
Bottom line: An external preamp is a great second step to improve your sound quality or to obtain more sound variety, but don’t make the second step before you’ve made the first. You can make great recordings with just your audio interface’s internal preamps and one or two high quality condenser mics.
How do I tune my lc2i?
How do you wire a lc2i amp?
Add amplifiers like a PRO! AudioControl LC2i-PRO overview
How hot is too hot for amp?
Amps can reach 90 C and still continue to work. The amp will automaticly shut down if he reaches high temperatures so dont worry about it. If a sub exceeds its temperature tolerance point it will start to smell like something is hot. Dunno if it will start to smell in a sealed enclosure tho.
Do amplifiers lose power over time?
Actually amps can lose power over time depending on how the amp was treated.
Can you use a LC2i with a 4 channel amp?
The LC2i has two channels for speakers and two for sub. A left and right for each. If you really wanted to connect 4 speakers to a 4 channel amp getting signal from the “Main” outputs of the LC2i you could, but you won’t have fader control for front to back.
Does preamp improve sound?
What’s the point of a preamp?
In a home theatre system, the pre-amplifier performs two main functions: it handles switching between different line level sources and boosts the signal before sending it to the amplifier. A weak electrical signal becomes strong enough for additional processing, preventing noise and offering cleaner output.