What is the mixing ratio for Nason paint?
Nason Finishes recommends using a ratio of 8:1/2:4, or 8 parts of Nason base coat to 1/2-part base coat activator to 4 parts base coat reducer. Failure to mix the paint properly can clog your spray gun. If you’re using aerosol cans, the paint should be properly mixed in the can for you, so skip this step.
Is Nason reducer a urethane?
Nason® SelectPrime™ 421-19 (gray) is a 2K Urethane Primer-Filler.
How do you use Nason ful base?
All Nason® primers, primer-surfacers and sealers as locally permitted. Apply two medium wet coats or to hiding. Flash each coat to dull/dry. For metallic colors, use a mist coat in conjunction with the final coat for best flake control.
Is Nason ful base acrylic or urethane?
Nason Ful-Thane IS Quality Single-Stage Topcoat
A urethane single-stage topcoat that provides good quality and performance and features a wide range of sparkling metallic and rich solid colors.
Does Nason ful base need clear coat?
Ful-BaseⓇ B/C Basecoat Color must be clear coated. Do not apply if less than 50°F. VOC REGULATED AREAS: These directions refer to the use of products which may be restricted or require special mixing instructions in VOC regulated areas.
How do you mix a base coat and reducer?
How to Mix Paint & Base Coat – YouTube
How do you mix car paint with reducer?
How To Mix Car Paint – A Quick Paint Mixing Tip with Kevin Tetz – Eastwood
What does urethane reducer do?
A urethane reducer allows you to adjust the consistency of the paint to make it easy to spray on the car surface. The reducer then evaporates, allowing the paint to set and harden.
How long does it take for Nason paint to dry?
Dry Time
| Air Dry | Force Dry |
|---|---|
| Dust free: 30 minutes at 70°F | Force dry: 20-30 minutes at 120-140°F |
| Tack free: 45-60 minutes at 70°F |
How do you mix Nason basecoat?
Mix 2 parts NasonXL Basecoat Color to 1 part NasonXL Reducer. Thin to spray viscosity of 16 secs with #4 Ford @ 77°F/25°C for spraying. Apply 2 to 3 single coats with 4 – 8 minute flash time between coats.
Do you put activator in base coat?
All you do is add reducer in base coats for the mixing ratio. Because you’re not adding any catalyst or hardener or an activator, you don’t have to worry about hardening. Base coats are always mixed with reducers, a 50:50 ratio.
Who makes Nason automotive paint?
Axalta Coating Systems
And remember… Nason Finishes is produced by Axalta Coating Systems, a world leader of respected and trusted refinish paint brands.
What is the flash time for Nason base coat?
15 – 20 minutes
Flash off for 15 – 20 minutes before applying clear.
How much reducer do you add to paint?
Very easy. 1 cup of base (your paint color) + 1 cup reducer = ready to paint. Your paint never goes bad. If you have left over, just cap it in a glass jar or your paint can and seal it up.
Do you use reducer with base coat?
Base coats are always mixed with reducers, a 50:50 ratio. The same as a (1:1) ratio. 1 pint of reducer and pint of base, mix it up and there’s your paint.
How do you mix reducer?
Auto Painting : How to Mix Auto Paint – YouTube
Do you mix reducer with clear coat?
How to Mix Clear Coat for Car Paint – YouTube
Can you use urethane reducer in base coat?
Formulated as high quality, urethane reducer, to produce a smooth and even flow-out for applications. It can be used in any 2K urethane primer, clear, topcoat and many base-coats that do not require a stabilizer or reactive reducer.
How do you mix paint with reducer?
How do you mix paint and reducer?
What is the top brands of automotive paint?
World’s top automotive paint and coating manufacturers
- Sherwin Williams. Sherwin Williams was founded in 1866 by Edward Williams, Henry Sherwin.
- PPG Industries. PPG Industries was founded in 1883 by John Baptiste Ford, John Pitcairn Jr.
- AkzoNobel. AkzoNobel was founded in 1994.
- Nippon Paint.
- RPM International Inc.
What type of paint is Nason?
A solventborne basecoat designed for overall repairs to OEM basecoat/clearcoat finishes.
How long can you leave base coat before clear coat?
30 minutes
Clearcoat Spray Paint
Allow 30 minutes after base coat color has been applied to apply the clear coat. Apply 4-5 wet (but not dripping) coats waiting 10+ minutes in between coats. Each coat should be dry to the touch (not tacky) before moving on to the next.
How many coats of base coat should I apply?
Apply 2 coats of the base coat, and then wait for the paint to dry completely before sealing with 2 coats of clear coat.