What is clethodim 2ec used for?
Clethodim 2E is a selective post-emergence herbicide used to control annual and perennial grasses in a wide variety of broad leaf crops including soybeans, cotton, flax, peanuts, sunflowers, sugarbeets, potatoes, alfalfa and most vegetables.
What herbicide group is clethodim?
WEED RESISTANCE MANAGEMENT For resistance management, LPI Clethodim is a Group 1 herbicide.
What is the active ingredient in clethodim?
ACTIVE INGREDIENT: By Wt. *(E)-2-[1[((3-chloro-2-propenyl)-oxy)imino]propyl]-5-[2-(ethylthio)propyl]-3-hydroxy-2-cyclohexen-1-one Contains 2.0 lbs. clethodim per gallon.
Is clethodim restricted?
NOTE: If Clethodim 2 EC Herbicide is applied as a spot treatment, care must be taken to not exceed the maximum rate allowed on a “per acre” basis or crop injury may occur. Restrictions • Do not apply Clethodim 2 EC Herbicide by chemigation in the states of Idaho, Montana, Oregon and Washington.
Can you mix Clethodim and glyphosate?
Glyphosate + clethodim mixture increases herbicide effectiveness. Low doses of herbicides are an important tool in integrated weed management. Synergism occurred at low doses for control and at all doses for dry mass.
How long does it take for Clethodim to work?
However, like Clethodim, it’s a fairly slow killer, and often takes 10 to 12 days to fully kill unwanted grasses in plots.
Can you mix glyphosate and Clethodim?
Sourgrass is one of the most problematic weeds in Brazil, with glyphosate resistance. Glyphosate + clethodim mixture increases herbicide effectiveness. Low doses of herbicides are an important tool in integrated weed management. Synergism occurred at low doses for control and at all doses for dry mass.
What is the mix rate for clethodim?
When using hand sprayers or high-volume sprayers utilizing hand guns, mix ¼% to ½% (0.33 oz. to 0.65 oz. per gallon) CLETHODIM 2E and treat to wet vegetation, while not allowing runoff of spray solution. For uses requiring crop oil concentrate, include crop oil concentrate at 1% (1.3 oz. per gallon) by volume.
Is clethodim residual?
When sprayed on broadleaf plants, clethodim does not inhibit ACCase in the same way it does with grasses, giving it high selectivity and virtually no crop effect. It is only active as a foliar spray and is not taken up from the soil solution, therefore there is no residual activity.
Is clethodim hazardous?
EMERGENCY OVERVIEW: CAUTION! The product is an eye irritant and may cause corneal injury. The product is an environmentally hazardous substance. The product may be harmful if swallowed or inhaled.
Do you need crop oil with Clethodim?
Apply CLETHODIM 2E at the high rate recommended for annual grasses (16 fl. oz. per acre) when the grass height is at the low end of the range (application to larger grasses may not provide adequate control). Add a crop oil concentrate containing at least 15% emul- sifier at 1 quart per acre.
Can you mix Clethodim and 24d?
Don’t tank mix them together or you will get severe antagonism. 16oz per acre of a 1lb AI clethodim or 8 oz per acre of a 2lb AI but that needs oil with it.
Do you need a surfactant with Clethodim?
For these grass selective herbicides to be effective a surfactant should be added to the tank mix. These surfactants will increase the efficiency of the herbicide and is critical for good grass kill when using Select (clethodim), Poast (sethoxydim), or any of their generic equivalents.
How much surfactant do I add to Clethodim?
If you are using Non Ionic Surfactant you would mix 2 tsp per surfactant with approx. . 4 oz Grass out in one gallon water over 1000 sq feet.
What is Section 3 herbicide used for?
SECTION THREE HERBICIDE is a selective postemergence herbicide for control of annual and perennial grasses. SECTION THREE HERBICIDE does not control sedges or broadleaf weeds.
What is Section 3 herbicide?
Section Three Herbicide is a systemic herbicide which is translocated from the treated foliage to the growing points of the leaves, shoots and roots. Uptake into the plant is primarily through its leaves. Thorough coverage of the foliage is important for consistent grass control.
How much surfactant do I add to clethodim?
How much surfactant per gallon does a clethodim use?
0.33 oz. per gal.
For uses requiring non-ionic surfactant, include non-ionic surfactant at 1/4% (0.33 oz. per gal.) by volume. NOTE: If CLETHODIM 2 EC HERBICIDE is applied as a spot treatment, do not exceed the maximum rate allowed on a “per acre” basis or crop injury may occur.
How long after spraying Clethodim can you plant?
DO NOT plant rotational crops until 30 days after application of Clethodim 2EC unless the crop is listed on Clethodim 2EC label. Application on Long Island, New York, is restricted to no more than 16 fl oz of Clethodim 2EC {0.25 lb ai) per acre per year.
Is Clethodim carcinogenic?
inhalation) Clethodim is classified as a “Not Likely” carcinogen ‘A dermal absorption factor of 30% is used for these risk assessments, based on the results of a dermal absorption study (MRID 41030202).
How much surfactant is needed for a gallon of clethodim?
When reading the label on clethodim, it said for spot spraying and hand sprayers to use . 33-. 65oz of clethodim per gallon of water and 1.33oz of concentrated crop oil per gallon of water.
How much surfactant per gallon does a Clethodim use?
Do you need a surfactant with clethodim?
How do you mix a clethodim?
When using hand sprayers or high volume sprayers utilizing hand guns, mix 1/4% to 1/2% (0.33 oz. to 0.65 oz. per gallon) CLETHODIM 2E and treat to wet vegetation, while not allowing runoff of spray solution. For uses requiring crop oil concentrate, include crop oil con- centrate at 1% (1.3 oz.