What years did Dodge use Dana 60?
Dodge used a Dana 60 up to 2002.
What axle is on a 2001 Ram 2500?
Dodge Ram 2500 and Dodge Ram 3500 4×4 trucks for the model years of 2000, 2001, and 2002 all use Dana-Spicer Model 60 248 Front Beam Iron (FBI) drive axles. Outwardly, these solid beam axles look very similar to the preceding models; however, relatively few parts were carried over from the 1999 and prior axle.
What Dodge trucks have Dana 60 axles?
Most 1994-2002 Dodge Ram 2500 with a gas V6 and V8 engine used the Dana 60 Full Floating Rear Axle.
Is a Ford Dana 60 the same as a Dodge Dana 60?
These axles are all exactly the same. If there are 4 bolts, then you have either a Dodge or Ford Dana 60 axle. These two axles are not identical.
Is a Dana 60 a good rear end?
If you want a big brute of a rear end under your car, look no further than a Dana 60. Even in the heyday of muscle cars, Dana 60 rear differentials were renowned for their strength, along with their difficulty to locate. Today, they’re actually incredibly easy to find.
Is the Dana 60 a good axle?
Like we said above, the Dana 60 is the stronger axle. If you want to run big tires or big power you need a Dana 60 axle. At the same time, the Dana 44 is a great axle if you don’t need giant tires or big power. Most people don’t realize how heavy a Dana 60 is and how much unsprung weight affects handling.
What axles are in a Dodge 2500?
However, most of the 2500 and all 3500 Rams use Dana 60 front axles. The 1500 Rams and some early light duty 2500 Rams used a 9.25 Chrysler (Spicer) axle in the rear. A Dana 60 rear axle was used on heavy-duty 2500 V8 Rams.
What did Dana 70 come in?
The first Dana 70 front axle was used in 1958 by Dodge in the W300, in both 4.88 and 5.87 ratios. International started using Dana 70 front axles in the late 1960s. Both companies used Dana 70 front axles until the mid-1970s (Dodge W300 pickup up until 1978, discontinued in 1979).
Is a Dana 60 a 1 ton axle?
The Dana 60 and Dana 70 are two heavy-duty variants in the Dana axle line, and are typically found in 3/4 ton and 1 ton pickup trucks.
Which is stronger Dana 60 or Ford 9?
See all 34 photos With its huge 9-inch ring gear, a beefy Dana 60 should be stronger than a 9-inch Ford. But as these Hoosier Gear photos show, the Dana 60 (left) has only a 1.062-inch hypoid offset, compared to the Ford’s larger 2.250-inch (right).
What is stronger Dana 60 or Ford 9-inch?
How much HP can a Dana 60 handle?
Additionally, the Dana 60 (S60) from Strange comes equipped with their beefy 35-spline alloy axles and carrier that can handle over 1,000 horsepower. A vintage Dana 60 like ours with its stock 23-spline axles and clutch-type Sure-Grip is limited to roughly 700 horsepower of sticky tire, strip action.
How do I identify the front axle on a Dana 60?
1959-1979 Ford Dana 30, Dana 44, and Dana 60 front axles were stamped on the front of one of the tubes (usually the left tube) with an axle identification or Bill of Material (BOM) Number.
Which is better Dana 60 or Dana 70?
The torque rating for a stock Dana 70 axle shaft is 8966 ft/lbs, which is almost 50% stronger than the stock Dana 60 axle shaft, which has a rating of 6044 ft/lbs.
Is Dana 44 better than 60?
Which is stronger Dana 60 or Ford 9 inch?
What axle is in my Ram 2500?
Axles. The Dodge Ram features a wide variety of axles. For the front axle of 4×4 Rams, a Dana 44 was used on all 1500 Rams and the early (light-duty) 2500 Rams. However, most of the 2500 and all 3500 Rams use Dana 60 front axles.
Are Dodge and Chevy Dana 60 the same?
Absolutely! The GM Dana 60 parts you have and the Dodge Dana 60 parts you have are interchangeable. Since you are sticking with 4.10:1 ratio gears, there isn’t even a carrier split to worry about. The 3.55:1 ratio gears and 4.10:1 ratio gears ride on the same carrier.
Is a 14-bolt A 1 ton axle?
The 14-Bolt Is The Ford 9-Inch Of 1-Ton Trucks
Every diesel-powered pickup sold in the United States for the last 10 years has a full-floating rear axle.
How do I know if I have a Dana 44 or Dana 60?
Many Dana axles have the model ID cast into the fins or centersection. Look for a “44” or “60” cast into the reinforcement ribs. The number can usually be found on the lower right side rib below the differential cover, but it may also be found on other ribs or on top of the main cast structure.
How do I know what rear axle I have in my Dodge?
Stamped Number on the Axle
To figure out exactly what axle you have, you can look for the Dana stamped bill of materials number. This stamped number can usually be found on the righthand side or on the longer axletube on the same side of the tube as the differential cover, facing the rear of the truck.
Is a Dana 70 better than a Dana 60?
Is Dana 80 stronger than 14 bolt?
By the numbers, the load-carrying and therefore torque capacity of the three axles from weakest to strongest is: 14-bolt, Dana 70, and Dana 80.
Which is better Dana 44 or Dana 60?