Can we ping from L2 switch?

It’s not possible to ping from the switch without an IP configured (management vlan). If an IP is configured on the switch, ip default-gateway is required in order to ping a device in another subnet than the management vlan. 3560 has L3 capabilities but you can use the switch as L2 switch (no ip routing).

Table of Contents

Can one VLAN ping another?

By default Vlans don’t ping each other as they are designed to fragment and isolate devices within the network (this is the logic when working on vlans on layer 2). If you wish to have Vlans communicating with each other then this is accomplished at layer 3 via a router.

How do I ping in Packet Tracer?

In the Desktop tab, click Command Prompt. . b. Type the ping command and the IP address for S1, and press Enter. Packet Tracer PC Command Line 1.0 PC> ping 192.168.

Can I ping a switch?

Like with every host using the IP protocol, without the default gateway, your switch should be able to ping anyone in its own IP subnet but won’t be able to ping anyone outside its own subnet.

Does ping work on layer 2?

The ping command uses the services of the Internet Control Message Protocol (ICMP), the latter being encapsulated in the IP header. Therefore, the ping utility operates basically on layer 3 (the Network layer) of the OSI model.

Can a Layer 2 switch route VLANs?

You can configure one or more VLANs to perform Layer 2 bridging. Thus, MX Series routers or EX Series switches can function as Layer 2 switches, each with multiple bridging, or broadcast, domains that participate in the same Layer 2 network. You can also configure Layer 3 routing support for a VLAN.

How do I ping a VLAN?

Use a extended ping command by using the source address from an SVI interface you’ve created towards the IP address of the another SVI on this switch. Once these interfaces are up, and you have setup the IP addresses on the hosts belonging to them, you are able to see the ARP table for each L3 interface (SVI).

How do I ping two networks?

You can use the ping command to verify the connectivity between two network devices that are IP (Internet Protocol) based. To ping another network device using a computer running Windows, complete the following: To bring up the run dialog, press the Windows key + R. Type cmd and press Enter.

How do I ping an IP address?

How to Ping an IP Address

Open the command-line interface. Windows users can search “cmd” on the Start taskbar search field or Start screen.
Input the ping command. The command will take one of two forms: “ping [insert hostname]” or “ping [insert IP address].”
Press Enter and analyze the results.

What is ping command in Cisco?

The ping command in Cisco IOS (and other operating systems) is used to test the accessibility of devices on a TCP/IP network. Cisco devices also support the extended ping command that allows you to perform a more advanced check of the host reachability and network connectivity.

Can we ping switch to router?

You can ping router to router because L2 works just fine through the switch and each router is aware of the other network. You need a router in the middle to be a defalt gateway for the switch if you want it to ping all networks .

What is ping command in switch?

ping. Use the ping command to send Internet Control Message Protocol (ICMP) echo request packets to another node on the network.

What OSI level is ping?

layer 3

Can we give an IP to a Layer 2 switch?

Contrary to Router/Firewall configuration, Layer 2 Switch has ports configured as Layer 2 which can’t be given an IP address, instead SVI (Switched Virtual Interface) needs to be assigned an IP address. Switch is assigned IP address to manage it via Telnet or SSH services.

Can IP address be assigned to layer 2?

Is a VLAN Layer 2 or 3?

VLANs are data link layer (OSI layer 2) constructs, analogous to Internet Protocol (IP) subnets, which are network layer (OSI layer 3) constructs.

Can you ping a VLAN IP address?

If your switch has L3 ability, you can issue the ip routing on the global config and then use the ping. Also the L3 communication between VLAN interfaces (as known as SVI on Cisco literature) starts to work. This test can be done either on the switch itself or by the hosts which are connected to their respective VLANs.

Can 2 VLANs talk to each other?

For the Engineering computers to be on the same network across multiple building floors, VLANs are used to isolate this traffic from marketing and accounting computers. Devices in different VLANs cannot communicate when only using layer 2 switches.

Can I ping any IP address?

Open the Command Prompt. Type “ping” in the black box and hit the space bar. Type the IP address you’d like to ping (e.g., 192.

How do I ping an IP?

How do I ping an IP and port?

In Windows, do this by typing “cmd” in the search box in the Start Menu and clicking the command prompt icon. In the command prompt window, type “telnet” followed by a space, then an IP address or domain name followed by another space, and then the port number.

What is use of ping command?

ping is the primary TCP/IP command used to troubleshoot connectivity, reachability, and name resolution. Used without parameters, this command displays Help content. You can also use this command to test both the computer name and the IP address of the computer.

What are ping command options?

ping -aAbBdDfhLnOqrRUvV6 -c count -F flowlabel -i interval -I interface -l preload -m mark -M pmtudisc_option -N nodeinfo_option -w deadline -W timeout -p pattern -Q tos -s packetsize -S sndbuf -t ttl -T timestamp option hop destinationping / Syntax

How do I ping a switch port?

The easiest way to ping a specific port is to use the telnet command followed by the IP address and the port that you want to ping. You can also specify a domain name instead of an IP address followed by the specific port to be pinged. The “telnet” command is valid for Windows and Unix operating systems.

Can I ping an IP address?

In Windows, hit Windows+R. In the Run window, type “cmd” into the search box, and then hit Enter. At the prompt, type “ping” along with the URL or IP address you want to ping, and then hit Enter.

Can we ping from L2 switch?