What is Ford VCM II?
Ford Vehicle Communication Module II (VCM II)
Authentic Ford OEM diagnostics scan tool that works with the Ford IDS diagnostics application running on a PC to diagnose Ford, Lincoln, and Mercury vehicles. Ford and VCM II are used under license from Ford Motor Company.
What is Ford VCI software?
Ford Diagnostic & Repair System (FDRS) – The next generation factory Ford Motor Company vehicle diagnostic Software designed for use with VCM II, VCMM and J2534 compatible Vehicle Communications Interfaces (VCI). FDRS provides complete dealership level vehicle diagnostic coverage for some 2018 and forward vehicles.
How do you reset a Ford VCM 2?
Shut down the IDS application if it is running. Disconnect the VCM II DLC cable from the vehicle. Disconnect the VCM II USB cable from the VCM II and PC. Remove the rubber boot on the VCM II that is opposite the DLC connector to expose the Recovery Mode Switch.
What software do Ford technicians use?
Integated Diagnostic Software (IDS) – The factory Ford Motor Company vehicle diagnostic software provides complete dealership level vehicle diagnostic coverage for all 1996 to present Ford, Lincoln and Mercury vehicles.
What does Ford IDS stand for?
Ford’s Integrated Diagnostic System (IDS): This is the current OEM tool for all Ford/Lincoln/Mercury dealers. Introduced to the Ford dealer service departments for model year 2005, this PC based tool covers all Fords models from 1996 to current year.
What can Ford IDS do?
Ford Integrated Diagnostic Software (IDS)
The Ford IDS and FDRS software is the only software that provides complete diagnostic coverage, including module programming and key programming of 1996 to current and future Ford and Lincoln vehicles.
Is FORScan the same as IDS?
IDS is comparable to the FORScan software. IDS is also dependent on the VCM. Depending on the software level of IDS, the VCM 1 and VCM 3 will time out. The VCM 3 with the latest software and firmware will access protected networks.
What scan tool does Ford use?
The Ford dealer techs have had access to two tools for scanning Ford products: the IDS (Intergrated Diagnostic System) and the ‘NGS. Both the ‘NGS’ and the IDS are available to the aftermarket throught OEMTools.com.
How do you program a Ford ECM?
How to Reprogram Ford PCM ECM reflash “Uninstall Install aftermarket …
Will FORScan work with VCM?
FORScan can only work with VCM using J2534 Passthru interface.
Can you use VCM with FORScan?
Forscan uses the same Bosch VCI manager that IDS Installs during IDS set up. The VCI manager can be installed separately by going to this site at Ford https://www.motorcraftservice.com/diagn goryId=276 And download and then install VCI 1.0. 0.10 or If you have an older VCM2 or a “Clone” this one 2.3.
Is Ford an OBD2?
ANCEL FD500 ford obd2 scanner is a specific version which design for Ford Group, including Ford, Lincoln, Mercury. A specific car make series is borned as more people have demand on DIY, one unit can fix more than you can expect .
Do you have to reprogram a used ECM?
Reprogramming your ECM is necessary for keeping your vehicle control software up to date. Much like the operating system on your home computer, improvements in software are often made by your car’s manufacturer. The software can be updated simply by downloading and installing the latest version.
How much does it cost to have a PCM programmed?
Prices could range from $80 to $150, depending on the service location you choose. The process takes around about half an hour, but keep in mind that most auto-electricians charge you for at least one hour of work. PCM reprogramming is also one of the few times we’ll recommend a dealership over an independent mechanic.
Does Ford IDS work with Windows 11?
Note: VCMM Hardware requires DirectX 11 Version 10.1 or higher.
…
| Minimum Specifications for running Ford Diagnostic Software | |
| Operating Systems/Requirements | Windows 10 Professional |
|---|---|
| Internet Explorer Versions | IE 11 or Microsoft Edge |
| Memory (RAM) | 4 GB or greater |
| Processor | 2.1 GHz or greater Intel I5/ I7 Dual Core |
What OBD2 protocol does Ford use?
SAE J1850 PWM
Diagnostic bus/protocol used mostly on Ford. Uses pins 1 and 2, communication signal is differential and it’s rate is 41.6kB/sec.
Can I reprogram my own ECM?
How Do I Reprogram an ECM? It’s not like changing the oil in your garage — it requires expensive, professional tools. With these tools the whole process is fairly simple and it’s almost entirely automated. No parts need be removed.
Can I replace an ECM myself?
The parts themselves aren’t inexpensive (as long as you’re buying them from us!), plus high quality aftermarket and OEM ECMs can be easily installed yourself.
Is Ford updating PCM free?
A Ford PCM update will usually be free of charge if it is covered by an in-date warranty. If the PCM is a replacement or if it is not covered by a warranty, then getting it updated will cost between $80 and $150 for labor.
How do I know if my Ford PCM is bad?
Let’s get started!
- Your ‘Check Engine’ Light is On.
- Your Car Won’t Start or Starts Roughly.
- Sudden Loss of Gas Mileage.
- You Failed Your Emissions Test.
- Your Engine Stutters or Stalls.
- Erratic or Random Shifting.
- You’re Receiving a PCM-Related Error Code.
- What to Do If You Experience PCM Failure Symptoms.
How do I uninstall Ford ID?
Uninstall IDS using Start > All Programs > Ford Motor Company > Uninstall IDS.
Can you drive with OBD plugged in?
It’s completely safe to leave an OBD2 scanner tool plugged in while driving. In fact, it’s important to have your car running while you diagnose an engine code to avoid damaging the scanning software.
Will disconnecting battery reset ECU?
A. It depends on the car’s age and type of ECU used. On some older cars, disconnecting the battery will reset the system but in most new cars it does nothing, except potentially reset the clock and radio station presets.
How much does it cost to reprogram ECM?
These typically cost somewhere in the ballpark of $200-$400. Again, the actual cost of repairing and replacing the ECM will depend on the make and model of your car. If the engine control module just needs to be tested, analyzed, and reprogrammed, it should cost you between $150 and $300.
How do I know if my Ford ECM is bad?
The Most Common ECM Failure Symptoms
- Your ‘Check Engine’ Light Is On. Your car’s check engine light is a sort of catch-all that many people ignore.
- Your Car Won’t Start.
- Your Engine Stutters or Misfires.
- Sudden Drop in Fuel Economy.
- Sudden Loss of Acceleration.
- Your Engine Shuts Off for No Reason.
- Rough or Irregular Shifting.