What is Talas on Fox forks?
TALAS stands for Travel Adjustable Linear Air Spring, and while the name remains, the spring curve is not linear. Fox engineers developed an entirely new adjustable-travel air spring that closely resembles those used in Float forks.
How do you adjust a fox in Talas fork?
Turning the TALAS lever toward the “+” (clockwise) sets your fork in the long travel mode. When adjusting to long travel mode, your fork will extend once unweighted. Turning the TALAS lever toward the “-” (counter-clockwise) and compressing the fork sets your fork in short travel mode.
How much travel does a Fox 32 fork have?
100 mm
Starting at 2.98 pounds, the 32 Step-Cast (SC) fork is our lightest cross-country fork ever. Optimized for 100 mm of travel, the Step-Cast lower leg design and narrow crown spacing save weight while the 32 mm upper tubes maintain FOX ride quality. No Debug Key available as Do Not Track is enabled.
How much travel does a Fox 34 fork have?
How much travel do the new 2022 Fox 34 and Fox 34 SC have? The 2022 Fox 34 SC fork is available with 100mm, 110mm and 120mm of travel. Forks with 120mm of travel do not come with the negative air spring volume spacer installed, but forks set at 100mm do. A 110mm travel air spring kit is available to buy separately.
How do you put air in Fox Talas?
Using the Air Spring Settings table below, pump your fork to the appropriate setting using the FOX High Pressure Pump, then remove the pump.
…
Setting Sag.
| AIR SPRING SETTING guidelines | |
|---|---|
| Rider Weight | Air Pressure |
| 145 – 155 lbs. | 65 psi |
| 155 – 170 lbs. | 70 psi |
| 170 – 185 lbs. | 80 psi |
What PSI should my Fox Float be?
Page 7 2004 manual: “Note: Average setting range is from 50 to 300 PSI. DO NOT EXCEED 300 PSI. Replace the air valve cap before riding.”
How do I setup my Fox 32 forks?
Competitive Cyclist Guide to Fox 32 RLC Fork Set Up Shock Set Up
Is the FOX 32 a good fork?
But for lean XC racers looking for the lightest high-performance option, the Fox 32 SC gets the pick from us. If you’re after a lightweight XC fork, it’d be hard to recommend anything else – the Fox 32 Step-Cast is a brilliant performer, and is exceptionally lightweight.
How long does a FOX fork last?
Fox recommends that the minimum suspension fork and shock service is 125 hours of use, yearly, or whichever comes first. That is certainly on the longer side of things. Similar to changing the oil in your car, the more frequently you service your suspension, the better the fork will perform for longer.
What is the difference between Fox 32 and 34?
Roughly summed up, the 32 series of forks are made for cross-country and light trail use, the 34 forks are meant for all-around trail use, the 36 is for heavy-duty trail/all-mountain use, the 38 is for enduro riding and racing while the dual crown 40 is made for downhill and extreme gravity riding.
Is Fox 34 or 36 better?
The 2022 Fox 34 inherits 36 technology and comes out a smoother, faster fork. The Takeaway: Revised with a bit of the 36’s magic, the new 34 is a smoother, better-performing fork.
What PSI should my bike suspension be?
Often yes, usually rear shocks run 100-200psi, but fork psi varies a lot, depending on the design. Get the sag around 25% (maybe slightly less sag in the front than the rear) and see how it rides (that’s what really matters), adjust on the trail as needed.
How much air should I put in my Fox Float shock?
Add air pressure to the main air chamber in ~50 psi (3.4 bar) increments, slowly cycling the shock after every 50 psi (3.4 bar) addition.
What psi should I run my rear shock?
The exact PSI you end up with depends on how plush/firm you want the rear shock to be, but a good starting point is 1 psi for 1 lbs in weight of the rider (including riding gear).
How do I tune my Fox suspension?
How To Set MTB Suspension Sag » ACADEMY | FOX – YouTube
What PSI should my FOX shock be?
Do not exceed 300 psi (20.7 bar), the maximum FLOAT air pressure! Remove the pump. Sit still on the bike in your normal riding position, using a wall or a tree for support.
How long does a Fox fork last?
Is RockShox or Fox better?
Key points when comparing Fox and RockShox
– Both Fox and RockShox offer a range of suspension forks from lightweight XC race forks to long-travel downhill forks. – Results: RockShox dominates World Cup XC, while Fox is tops in World Cup DH racing.
How often should Fox forks be serviced?
around once per year
According to Fox Racing Shox, you should be servicing your fork and shock every 125 hours of ride time, or around once per year. If you break it down, this equates to roughly a 2.4 hour ride per week.
Is Kashima coating worth it?
So is it worth getting Kashima Coat? It definitely has some value, so it’s not completely worthless. In general, I believe it is safe to say that it is not worth it on rear shocks, since they generally have low amounts of friction and negligible durability concerns.
What psi should Fox shocks be?
FoX shocks should be left at the factory setting of 200 psi of nitrogen.
What does too much rebound feel like?
TOO MUCH REBOUND DAMPING (FORK)
Rough pavement makes the fork feel as if it’s locking up with stiction and harshness. Under hard acceleration exiting bumpy corners, the front end feels like it wants to “wiggle” or “tankslap.” The tire feels as if it isn’t staying in contact with the pavement when on the gas.
What PSI should my rear shock be at?
15-25% is appropriate.
What PSI should my Fox rear shock be?
250psi
If the shock body retracts into the air sleeve near bottom-out after the air is released from the positive chamber, attach a FOX high pressure pump and pressurize the shock to 250psi (17 bar). If the shock does not fully extend, it is in a “stuck down” condition.